قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)

Audi آودي آر8

2006–2024 · 1 أعطال موثّقة · 3 أسواق

النشرات الفنية (TSB) تعليمات إصلاح يرسلها المصنعون إلى وكلائهم بشأن مشكلات معروفة. ليست استدعاءات سلامة، لكنها كثيرًا ما تؤكد وجود عطل.

سنة الطراز
السوقالكلNA
نشرةحرجالمحركNA

نشرة

Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

NHTSA · نشرة المصنع10123969سنوات الطراز 2011–2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةحرجالمحركNA

نشرة

Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.

NHTSA · نشرة المصنع10122803سنوات الطراز 2011–2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulletin provides information for all gasoline engines when the MIL is on; DTC P240700 is stored - Fuel leak detection pump.

NHTSA · نشرة المصنع11039214سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · نشرة المصنع11034668سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulletin provides information regarding UV leak additive for finding oil leaks.

NHTSA · نشرة المصنع11028398سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · نشرة المصنع11025354سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This TSB provides information when the fuel tank cap seal is leaking, DTC P044200, P045600, and/or P00EF00 stored in ECM.

NHTSA · نشرة المصنع11022688سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulleitn provides information regarding UV Leak additive for finding oil leaks.

NHTSA · نشرة المصنع11022633سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

تطلب هذه الحلول المعلقة للخدمة (PSS) من الفنيين إدخال سجل في قاعدة بيانات PSS في الحالات التي يكون فيها مؤشر عطل الجهاز (MIL) مضاءً، مع وجود عطل في دائرة مضخة كشف التسرب في نظام التبخير (Evap)، رمز العطل DTC240700.

NHTSA · نشرة المصنع11009316سنوات الطراز 2023ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · نشرة المصنع11005851سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · نشرة المصنع11002215سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · نشرة المصنع11002115سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This Pending Service Solution (PSS) requests that technicians enter a record in the PSS Database in instances where the MIL is on and DTC P240700 is stored; Evap leak detection pump circuit.

NHTSA · نشرة المصنع10253248سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

This bulletin contains instructions for an oil leak that is due to excessive sealant used in a previous repair.

NHTSA · نشرة المصنع10153121سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

On-Hoist Inspection Section: Removed "Perform a coolant reservoir cap pressure test via ELSA -> Enter VIN # -> Repair manual Engine -> 4-Cylinder Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III) -> 19 Cooling System -> Coolant System/Coolant -> Cooling System, Checking for Leaks -> Pressure Relief Valve in Cap, Checking. Only the procedure ?Pressure Relief Valve in Cap, Checking? should be performed in the document Cooling System, Checking for Leaks

NHTSA · نشرة المصنع10120803سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · نشرة المصنع10119945سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

Supersedes Technical Service Bulletin Group 24 number 12-27 dated April 23, 2012. MIL is illuminated. Irregular engine performance. R8 Intake Air Hose leaking.

NHTSA · نشرة المصنع10124951سنوات الطراز 2011–2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

NHTSA · نشرة المصنع10124868سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالمحركNA

نشرة

Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · نشرة المصنع10121324سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.

NHTSA · نشرة المصنع11035854سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · نشرة المصنع11035829سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · نشرة المصنع11035828سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides informaiton when the engine is not running smoothly, misfiring.

NHTSA · نشرة المصنع11034728سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · نشرة المصنع11034657سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةطفيفالمحركNA

نشرة

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · نشرة المصنع11027356سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
الأقدم →

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).