تحل هذه النشرة محل النشرة (النشرات) الصادرة سابقاً والمدرجة أدناه. التغييرات مبينة باللون الأحمر.
09-012/21 12/13/21, 06/10/21 and 04/27/21
الوصف
قد يواجه بعض العملاء جميع الأعراض التالية:
لن يعمل قفل/فتح الأبواب باستخدام زر جهاز الإرسال عن بُعد.
1. لن يعمل قفل/فتح الأبواب باستخدام مستشعر اللمس الخاص بقفل/فتح الباب.
2. لن يبدأ تشغيل المحرك باستخدام مفتاح الإشعال.
3. يعمل جهاز الإرسال من تلقاء نفسه.
4. تنفد بطارية المفتاح بشكل أسرع من المعتاد.
5. الأعراض 1-3: قد يحدث ذلك عند تعرض جهاز الإرسال عن بُعد لحمل زائد، مما يؤدي إلى تشوه الأطراف الكهربائية وضعف التلامس مع البطارية. للقضاء على هذه المشكلة، تم تعديل هيكل جهاز الإرسال عن بُعد للحد من تشوه الأطراف الكهربائية.
الأعراض 4-5: قد يحدث ذلك عند تعرض جهاز الإرسال عن بُعد لحمل مفرط، مما يخلق فجوة حول الحشية تدخل من خلالها الرطوبة فتآكل لوحة الدوائر، وهو ما يؤدي بدوره إلى استنزاف بطارية المفتاح بشكل أسرع من المعتاد. للقضاء على هذه المشكلة، تمت زيادة سماكة جدار الهيكل على سطح تركيب الحشية، وتحسين قوة الترابط بين المكونات لمنع التشوه.
إجراء الإصلاح
إذا كانت البطارية تالفة أو مركبة بشكل غير صحيح، فاستبدل البطارية و/أو أعد تركيبها بشكل صحيح.
إذا كانت وظيفة توفير الطاقة عن بُعد متوقفة، وكانت البطارية سليمة ومركبة بشكل صحيح، فاستبدل جهاز الإرسال عن بُعد المعيب بجهاز معدّل وفقاً للتعليمات الواردة في MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING).
NOTE: لا تستبدل أجهزة الإرسال عن بُعد الأخرى الخاصة بالمركبة إذا لم تكن تعاني من أي مشكلة.
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.
NHTSA · نشرة المصنع10185957سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
NHTSA · نشرة المصنع10165350سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.
NHTSA · نشرة المصنع10120369سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.
NHTSA · نشرة المصنع10118478سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear: 1) Lane Departure Warning System (LDWS) warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. 2) High Beam Control (HBC) System warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear).
NHTSA · نشرة المصنع10118126سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".
NHTSA · نشرة المصنع11011138سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · نشرة المصنع11009639سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
NHTSA · نشرة المصنع11008573سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
NHTSA · نشرة المصنع10254190سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control
NHTSA · نشرة المصنع10252509سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
NHTSA · نشرة المصنع10240366سنوات الطراز 2023معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.
NHTSA · نشرة المصنع10186320سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit rust (A) on the front door quarter glass guide (B) where it contacts the door beltline molding (C). The paint on the quarter glass guide gets damaged from vibration when the door is closed and when driving. This concern is caused by the beltline molding contacting the quarter glass guide due to production variances. To correct this concern, a spacer has been attached at the contact area to assure an appropriate clearance between the beltline molding and the quarter glass guide.
NHTSA · نشرة المصنع10154453سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · نشرة المصنع10153338سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA · نشرة المصنع10153339سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.
NHTSA · نشرة المصنع10153294سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit the power window(s) not working properly (window does not move or has fallen into the door) and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding.To eliminate this concern, the shape of the door glass will be modified during mass production to prevent water entry to the power window regulator.
NHTSA · نشرة المصنع10153292سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA · نشرة المصنع10148072سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · نشرة المصنع10148071سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.
NHTSA · نشرة المصنع10144324سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Dealer Rework (DRW) 09 ? 2018 Mazda MX-5 Power Window Switch Concern: On affected vehicles, the driver power window main switch is not correctly assembled to the power window main switch door panel. There are 4 tabs (2 tabs on front side, 2 tabs on rear side) on the power window main switch affixed to the door panel. It is possible that 1 or 2 of the tabs are not locked, and there is a chance the switch will drop slightly when the power outer mirror switch is pushed.When the power window main switch part is assembled to the driver-side door trim by a jig in production, the power window main switch could have been unintentionally pushed vertically due to the jig misalignment.
NHTSA · نشرة المصنع10134937سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct this problem, the control logic of the BSM control modules has been changed.
NHTSA · نشرة المصنع10120383سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit a squeak noise at the rear beltline when the door glass moves up and/or down. This concern happens especially when the door glass is wet with moisture or after a car wash. This is caused by stick-slip noise occurring at the contact surfaces between the door glass and the weather strip. With repeated moving up and down, the anti-noise paint on the weather strip peels off. To prevent the stick-slip noise, a polyester film has been attached at the applicable location of the weatherstrip.
NHTSA · نشرة المصنع10120357سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).