Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.
NHTSA · نشرة المصنع10185955سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
NHTSA · نشرة المصنع10163333سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · نشرة المصنع10159199سنوات الطراز 2018–2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
في إطار دعم توزيع MRT الجديد، ستشحن Mazda إلى الوكلاء جهاز كشف التسربات التشخيصي متعدد الأغراض الجديد بدءًا من شهر مارس 2019. وسيتم نشر مقاطع الفيديو التدريبية على MGSS قريبًا، وستُراجع إجراءات دليل الورشة تدريجيًا.
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
NHTSA · نشرة المصنع10153331سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · نشرة المصنع10153304سنوات الطراز 2018–2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may complain that the the middle headliner looks loose at the center rear. This is caused by parts variation. To correct the concern, an additional fastener can be installed in the headliner.
NHTSA · نشرة المصنع10118475سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience poor a/c performance due to a slow refrigerant leak from the o-ring groove on the cooler pipe (high pressure side) at the expansion valve.
NHTSA · نشرة المصنع10105622سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience poor a/c performance due to a slow refrigerant leak from the o-ring groove on the cooler pipe (high pressure side) at the expansion valve.
NHTSA · نشرة المصنع10101455سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
NHTSA · نشرة المصنع10101101سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window.This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
NHTSA · نشرة المصنع10093144سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Workshop manual evap system leak inspection using the m-mds has been discontinued for some models. Instead, the workshop manual evap system leak inspection using evap leak tester will be used to troubleshoot evap system leaks.
NHTSA · نشرة المصنع10092322سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
NHTSA · نشرة المصنع10090903سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
NHTSA · نشرة المصنع11011140سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
NHTSA · نشرة المصنع11008578سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).