قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)
تسجيل الدخولإنشاء حساب
NANHTSA · نشرة المصنع11018204

النشرات الفنية

معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظار

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

يشمل: Mercedes-Benz C-Class W206 (سنوات الطراز 2023–2024) · Mercedes-Benz E-Class V213 (سنوات الطراز 2023) · Mercedes-Benz E-Class W214 (سنوات الطراز 2025) · Mercedes-Benz EQA (سنوات الطراز 2021) · Mercedes-Benz EQE (سنوات الطراز 2023) · Mercedes-Benz EQS (سنوات الطراز 2023) · Mercedes-Benz GLA II (سنوات الطراز 2024) · Mercedes-Benz GLC II (سنوات الطراز 2024–2025) · Mercedes-Benz GLE-Class GLE (W167/C167) (سنوات الطراز 2024–2025) · Mercedes-Benz GT II (سنوات الطراز 2024–2025) · Mercedes-Benz S-Class VII (W223) (سنوات الطراز 2021–2023) · Mercedes-Benz X166 (سنوات الطراز 2020)

الإشعار الرسمي ↗

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).