قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)
NANHTSA · نشرة المصنع11037487

النشرات الفنية

معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظار

Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: Driving style such as two footed driving where the pad might be in constant contact with the rotor. Brake pressure and application style (stopandgo traffic with consistent light brake pressure riding brakes where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 34 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to reassessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and reapply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

يشمل: Mercedes-Benz A-Class IV (W177) (سنوات الطراز 2020) · Mercedes-Benz C-Class type 204 (سنوات الطراز 2009) · Mercedes-Benz C-Class W205 (سنوات الطراز 2017) · Mercedes-Benz C-Class W206 (سنوات الطراز 2024–2026) · Mercedes-Benz CLA-Class II (سنوات الطراز 2020–2025) · Mercedes-Benz CLA-Class III (سنوات الطراز 2026) · Mercedes-Benz CLK-Class C209 (سنوات الطراز 2008) · Mercedes-Benz CLS-Class C219 (سنوات الطراز 2006) · Mercedes-Benz E-Class V213 (سنوات الطراز 2023) · Mercedes-Benz E-Class W214 (سنوات الطراز 2025) · Mercedes-Benz GLC II (سنوات الطراز 2025–2027) · Mercedes-Benz GLE-Class M-Class/GLE (W166/C292) (سنوات الطراز 2018) · Mercedes-Benz GLE-Class GLE (W167/C167) (سنوات الطراز 2023–2026) · Mercedes-Benz GT II (سنوات الطراز 2024–2026) · Mercedes-Benz S-Class W222 (سنوات الطراز 2017) · Mercedes-Benz SL-Class R232 (سنوات الطراز 2025) · Mercedes-Benz SLK-Class R172 (سنوات الطراز 2016–2017)

الإشعار الرسمي ↗

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).