Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Audi R8

2006–2024 · 1 generationen · 1 dokumentierte Mängel · 3 Märkte
Generationen
Alle GenerationenR82006–20241231083

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

Modelljahr
MarktAlleNA
BulletinKritischMotorNA

Bulletin

Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

NHTSA · Herstellerbulletin10123969Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinKritischMotorNA

Bulletin

Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.

NHTSA · Herstellerbulletin10122803Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulletin provides information for all gasoline engines when the MIL is on; DTC P240700 is stored - Fuel leak detection pump.

NHTSA · Herstellerbulletin11039214Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · Herstellerbulletin11034668Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulletin provides information regarding UV leak additive for finding oil leaks.

NHTSA · Herstellerbulletin11028398Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · Herstellerbulletin11025354Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This TSB provides information when the fuel tank cap seal is leaking, DTC P044200, P045600, and/or P00EF00 stored in ECM.

NHTSA · Herstellerbulletin11022688Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulleitn provides information regarding UV Leak additive for finding oil leaks.

NHTSA · Herstellerbulletin11022633Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This Pending Service Solution (PSS) requests that technicains enter a record in the PSS database in instances where the MIL is on, Eval leak detection pump circuit, DTC240700.

NHTSA · Herstellerbulletin11009316Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · Herstellerbulletin11005851Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · Herstellerbulletin11002215Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · Herstellerbulletin11002115Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This Pending Service Solution (PSS) requests that technicians enter a record in the PSS Database in instances where the MIL is on and DTC P240700 is stored; Evap leak detection pump circuit.

NHTSA · Herstellerbulletin10253248Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

This bulletin contains instructions for an oil leak that is due to excessive sealant used in a previous repair.

NHTSA · Herstellerbulletin10153121Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

On-Hoist Inspection Section: Removed "Perform a coolant reservoir cap pressure test via ELSA -> Enter VIN # -> Repair manual Engine -> 4-Cylinder Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III) -> 19 Cooling System -> Coolant System/Coolant -> Cooling System, Checking for Leaks -> Pressure Relief Valve in Cap, Checking. Only the procedure ?Pressure Relief Valve in Cap, Checking? should be performed in the document Cooling System, Checking for Leaks

NHTSA · Herstellerbulletin10120803Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · Herstellerbulletin10119945Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Supersedes Technical Service Bulletin Group 24 number 12-27 dated April 23, 2012. MIL is illuminated. Irregular engine performance. R8 Intake Air Hose leaking.

NHTSA · Herstellerbulletin10124951Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

NHTSA · Herstellerbulletin10124868Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · Herstellerbulletin10121324Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.

NHTSA · Herstellerbulletin11035854Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · Herstellerbulletin11035829Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · Herstellerbulletin11035828Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides informaiton when the engine is not running smoothly, misfiring.

NHTSA · Herstellerbulletin11034728Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · Herstellerbulletin11034657Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · Herstellerbulletin11027356Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).