Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

LexusLexus RC

2014–2025 · 1 generationen · 2 dokumentierte Mängel · 4 Märkte
Generationen
Alle GenerationenRC2014–2025222337

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleGering
Modelljahr
BulletinGeringMotorNA

Bulletin

DL: On December 20, 2022, a settlement of claims for certain low pressure fuel pumps was approved by the federal court. The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2013-2020 model year (MY) vehicles originally equipped with low pressure fuel pumps repaired under Safety Recall 20LA01 or Special Service Campaign 21LC01. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

NHTSA · Herstellerbulletin10235219Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

DL: On December 20, 2022, a settlement of claims for certain low pressure fuel pumps was approved by the federal court. The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2015-2020 model year (MY) vehicles that were not previously involved in a Safety Recall or Special Service Campaign related to the low pressure fuel pump. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

NHTSA · Herstellerbulletin10235220Modelljahre 2015Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

TSB: Some 2013 ? 2020 model year Lexus vehicles may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.

NHTSA · Herstellerbulletin10235215Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Oil Viscosity Applicability and Cfhange Interval Guide

NHTSA · Herstellerbulletin10205358Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Oil Viscosity Applicability and Cfhange Interval Guide

NHTSA · Herstellerbulletin10205359Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

TT: TMS has discovered the current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS or 8AR-FTS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS or 8AR-FTS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

NHTSA · Herstellerbulletin10152276Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

"tt: Tms has discovered the current engine active test control the injection mode is not operating as desired when controlling the direct injectors manually on 2gr-fks or 8ar-fts engines. When direct injection is started and then stopped using the active test, current ecu logic does not turn off the direct injectors and can cause dtcs p017200, p017500 and p0160300. In order to avoid this condition, technicians should raise engine rpm when changing from direct injection active test to port injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2gr-fks or 8ar-fts equipped vehicles. Note: If the active test is used multiple times without using this procedure to raise engine rpm, it may be necessary to reset learning values for fuel trim and air to fuel ratio before returning vehicle to customer."

NHTSA · Herstellerbulletin10093695Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).