Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda 6

2002–2024 · 3 generationen · 60 dokumentierte Mängel · 6 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
MarktAlleNA
6 III · 2012–2024
BulletinMittelMotorNA

Bulletin

Please be advised that the valve stem seals assigned to the 2.5 Skyactiv Turbo engines in GEPC are incorrect. The Diesel Valve Stem seal SH09-10-1F5A, which is for Diesel engines, is currently listed for these models in GEPC. Please ensure that the proper valve stem seals are used for the 2.5 Skyactiv Turbo engines affected by SSPD5 have the correct valve seal part number PY8W-10-1F5 installed on PYT engines to avoid any potential issues.

NHTSA · Herstellerbulletin11000679Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinMittelMotorNA

Bulletin

Some vehicles may exhibit an engine no start in ambient temperatures below -4 degree fahrenheit (-20 degree celsius) after driving for 10 - 20 minutes and then parking the car for about one hour. This may be caused by the contact point of the main relay freezing due to moisture inside the main relay.

NHTSA · Herstellerbulletin10097813Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 I (GG1) · 2002–2008
BulletinMittelMotorNA

Bulletin

Engine cranks but no start - sets diagnostic trouble code (dtc) p0335. *tt

NHTSA · Herstellerbulletin10003942Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.

NHTSA · Herstellerbulletin11020037Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.

NHTSA · Herstellerbulletin10254186Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.

NHTSA · Herstellerbulletin10235702Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Ignition does not turn off when pressing start/stop button

NHTSA · Herstellerbulletin10213409Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.

NHTSA · Herstellerbulletin10210884Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Maintenance monitor engine oil data reset

NHTSA · Herstellerbulletin10186926Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

If you receive a customer complain of lack of power, rough idle, engine noise with stored DTC's P0340:00, P0304:00, P3400:00, P349B:00, and/or P3498:00, perform the following.

NHTSA · Herstellerbulletin10153295Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

A tapping/rattling noise may be noticed from the valve train area. This condition usually occurs after the engine has been turned off at normal operating temperature and then not warmed up to full operating temperature during the next series of cold starts. This operating condition can occur, for example, on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.)

NHTSA · Herstellerbulletin10134943Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

When pressing the start/stop button, the ignition may not turn off on some vehicles equipped with a gate type at shifter. Although the shift lever is in p position and the engine shuts off normally, the ignition may stay on (in accessory mode). This concern may be caused by a worn switch unit. To eliminate this concern, the switch unit material has been changed to improve wear resistance. Modified switch units have been established as new service parts.

NHTSA · Herstellerbulletin10105637Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Some vehicles may experience a rough idle with the mil on and dtc p0015 / p0524 stored in memory.P0015:00 - exhaust cmp timing over-retardedp0524:00 - engine oil pressure too lowthis is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or ocv. The temporary entry of the foreign object triggers a mil illumination, but rough idle will not be produced until a later time.

NHTSA · Herstellerbulletin10098548Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Some vehicles may experience a rough idle with the mil on and dtc p0015 / p0524 stored in memory. P0015:00 - exhaust cmp timing over-retarded p0524:00 - engine oil pressure too low this is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or ocv. The temporary entry of the foreign object triggers a mil illumination, but rough idle will not be produced until a later time.

NHTSA · Herstellerbulletin10098209Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Some customers may complain about an unusual noise coming from the engine compartment for about 20 sec-onds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction.

NHTSA · Herstellerbulletin10097324Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

When pressing the start/stop button, the ignition may not turn off on some vehicles equipped with a gate-type at shifter. Although the shift lever is in p position and the engine shuts off normally, the ignition may stay on (in accessory mode).This concern may be caused by a worn switch unit. To eliminate this concern, the switch unit material has been changed to improve wear resistance. Modified switch units have been established as new service parts.

NHTSA · Herstellerbulletin10093141Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

There is an early and late style rear hub (d-codes 26-112 / 26-112z) as shown below. As stock is exhausted of the early hubs they will be placed in a c (component) supersession so that a new hub and any additional parts that may be needed are shipped at the same time. When gepc vin lock identifies an early part number, as with all c (component) supersessions, order that part number. Do not order a newer part later in the supersession chain. If you order the early part specified by the vin, a new part and any additional parts that may be needed will ship. If you order a newer part, just the newer part will ship. No additional parts that may be needed will ship.

NHTSA · Herstellerbulletin10092235Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Mazda connect shuts down and does not reboot. Some vehicles may experience mazda connect infotainment system shutting down with a few minutes after ignition is turned on, and will not reboot. It will only reboot after ignition is turned off and then turned on again. This is caused by an internal malfunction of the connectivity master unit (cmu) hardware.

NHTSA · Herstellerbulletin10076688Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 III · 2012–2024
BulletinGeringMotorNA

Bulletin

Mazda: Due to drop in engine oil pressure, some vehicles experience a rough idle, caused by foreign object(s) stuck on ocv or oil pump pressure relief valve. Model 2012-2014 mazda3, mazda6, cx-5. *pe

NHTSA · Herstellerbulletin10056056Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 II (GH1/GH2) · 2007–2012
BulletinGeringMotorNA

Bulletin

Mazda: There is a rattle noise from the engine due to a stretched timing chain. *rm updated 4/18/2012. *kb

NHTSA · Herstellerbulletin10039251Modelljahre 2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 II (GH1/GH2) · 2007–2012
BulletinGeringMotorNA

Bulletin

Mazda: Purge valve contact/hard rattle noise. Some vehicles may experience a rattle or a loud tick noise from the engine compartment during purge valve operation (the noise is loudest during 30%-60% duty cycle). This may be a hard contact noise caused by misalignment of the purge valve, rubber grommets, or attaching hoses forcing contact with the pcm, pcm bracket, metal bracket or an excessive valve tick noise. *pe

NHTSA · Herstellerbulletin10032668Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
6 I (GG1) · 2002–2008
BulletinGeringMotorNA

Bulletin

Aufleuchten der MIL (DTC P2006), freiwillige Emissionsrückrufaktion 4807h, und OBD-II-Konformität, freiwillige Emissionsrückrufaktion 4907h. *nj

NHTSA · Herstellerbulletin10023192Modelljahre 2006Automatisch übersetzt · Original: EnglischDetails ansehen →
6 I (GG1) · 2002–2008
BulletinGeringMotorNA

Bulletin

Delayed throttle response during low speed acceleration. *tt

NHTSA · Herstellerbulletin10016873Modelljahre 2005Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).