Der vordere äußere Sockel der Sitzschiene des Fahrersitzes kann anfällig für Ermüdungsbruch sein. Ein Bruch dieses Sockels würde ein begrenztes Kippen der Fahrersitzbaugruppe bei Beschleunigung oder Verzögerung ermöglichen. Ein Bruch der Halterung könnte unter Umständen die Kontrolle des Fahrers über das Fahrzeug beeinträchtigen und zu einem Unfall führen. Abhilfe: Eine Verstärkung wird an der Sitzschiene angebracht, oder die Sitzschiene wird bei einem Bruch ersetzt.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
Transport Canada17. Mai 19881988066Modelljahre 1983–1984Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
The rear seat belt retractors may allow twisted webbing to enter the retractor housing. Twisted webbing may wedge between the retractor spool and housing producing a jammed retractor condition which interfered with webbing retraction and withdrawal.
Transport Canada14. Juni 19851985074Modelljahre 1982–1983Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Rear seat belt retractors may allow twisted webbing to enter the retractor housing and jam the retractor. Consequence of defect: A jammed retractor would interfere with webbing retraction and withdrawal. This will discourage seat belt usage.
NHTSA · USA21. Mai 198585V067000Modelljahre 1982–1983Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On vehicles with optional front seat recliners, the upper shoulder screw that attaches the driver's seat back frame to the recliner mechanism may be susceptible to fatigue fracture. If fatigue fracture of the recliner upper attachment screw were to occur on the driver's seat, the seat back could rotate rearward to a near horizontal position without warning potentially affecting the driver's control of the vehicle.
Transport Canada19. Juli 19841984087Modelljahre 1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
When severely loaded by a frontal impact, the seat belt webbing may contact the leading edge of the front seat-back stell reinforcement plates. This may cause the seat belt webbing to be abraded, cut or completely severed, thereby significantly increasing the risk of serious personal injuries.
Transport Canada19. Juni 19841984078Modelljahre 1981–1983Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
Transport Canada17. Dez. 19831983114Modelljahre 1984Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
The portion of the roof above frame (rail) to which the shoulder belt is anchored may have a slot that can compromise the strength of the shoulder belt anchor under certain severe loads. (the suspect area is not visible.) consequently, some vehicles included in this recall may not meet the 3000 pound anchorage strength requirements of federal motor vehicle safety standard 210, "seat belt assembly anchorages".
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).