Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Transport CanadaNov 24, 20212021723Model years 2006–2018View details →
On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.
Transport CanadaJul 20, 20172017363Model years 2016–2017View details →
The fuel pressure sensor may not have correctly tightened during assembly. Over time this may affect the seal and allow fuel odour to escape. This could ignite in the presence of an ignition source.
DVSA · United KingdomMay 26, 2016R/2016/080Model years 2005–2007View details →
null The sealing performance of the gasket seated between the fuel pressure sensor and the engine fuel delivery pipe could degrade over time. If this occurs, fuel could leak which, in the presence of an ignition source, could lead to a vehicle fire.
EU Safety GateApr 21, 2016A12/0512/16Model years 2005–2007View details →
The fuel pressure sensor gasket may degrade and allow fuel to leak into the engine compartment. In the presence of an ignition source the risk of fire is increased.
DVSA · United KingdomNov 24, 2014R/2014/135Model years 2007–2010View details →
In the front wipers on subject left hand drive cars there is high friction at the tightening surface between the wiper arm nut and the wiper arm that could result in the nut being insufficiently tight. If the movement of the wiper arm is restricted by an external load such as a build up of heavy snow on the windshield the wiper motor torque may exceed the wiper arm slipping torque and one or both wipers could become inoperative. If this happens then visibility could be reduced which could increase the risk of a crash.
DVSA · United KingdomApr 26, 2013R/2013/015Model years 2007–2010View details →
null The wiper arm nuts on the front wipers may be insufficiently tight. If the movement of wipers is restricted by an external load, such as a build-up of heavy snow on the windscreen, the wiper motor torque may exceed the wiper arm slipping torque, and one, or both, of the wipers could become inoperative. If this occurs, driver visibility could be reduced, which could lead to an accident.
EU Safety GateFeb 1, 2013A12/0166/13Model years 2010–2013View details →
Toyota is recalling certain model year 2006-2012 Lexus IS250 and IS350 vehicles manufactured August 23, 2005, through October 5, 2011; 2010-2012 Lexus IS250C and IS350C vehicles manufactured April 10, 2009, through October 6, 2011; and 2008-2011 Lexus IS-F vehicles manufactured December 14, 2007, through July 10, 2011. The nuts that fasten the wiper arms may be insufficiently torqued such that if the wiper arms are restricted by an external load, such as a buildup of heavy snow, one or both of the wipers may become inoperative.
NHTSA · United StatesJan 30, 201313V030000Model years 2006–2012View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).