Lectura libre · cuenta gratuita para colaborarSucesor de Anticars (2000)

Nissan Juke

2010– · 3 generaciones · 21 averías documentadas · 5 mercados
Generaciones
Año del modelo
Juke I · 2010–2019
LlamadaCríticoMotorEU

Un interruptor de encendido interno podría estar defectuoso

Un interruptor de encendido interno podría estar defectuoso. Como consecuencia, el motor podría calarse inesperadamente mientras se conduce y, en determinadas condiciones, es posible que el sistema de airbags del vehículo no funcione.

Safety Gate · UE29 ago 2018A12/1281/18Años modelo 2017Traducido automáticamente · original: inglésVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Fuel System

On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.

Transport Canada8 mar 20182018121Años modelo 2011–2012Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.

NHTSA · Estados Unidos7 mar 201818V156000Años modelo 2011–2012Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorEU

Motorrijtuigen - krachtoverbrenging

Brandstofdruksensor niet correct vastgezet. Hierdoor kan de sensor onder invloed van warmte en trillingen losraken.

rdw23 mar 2015MGP150107Años modelo 2012–2013Mostrado en neerlandés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Sistema de combustible

En determinados vehículos, es posible que el sensor de presión de combustible conectado al riel de distribución de combustible del motor no se haya apretado lo suficiente durante el ensamblaje del vehículo. Si el sensor se aflojara, el combustible podría filtrarse a través de una junta utilizada en la conexión entre el sensor y el riel. La fuga de combustible, en presencia de una fuente de ignición, podría provocar un incendio que cause daños materiales y/o lesiones personales. Corrección: Los concesionarios inspeccionarán el sensor de presión y lo apretarán según las especificaciones. Nota: Esta es una ampliación de la campaña 2012-074. Los vehículos que fueron reparados bajo la campaña anterior no están afectados, ya que esa reparación habría corregido la condición en cuestión.

Transport Canada28 nov 20142014539Años modelo 2011–2014Traducido automáticamente · original: inglésVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.

NHTSA · Estados Unidos28 nov 201414V683000Años modelo 2012–2014Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorJP

その他(燃料装置)

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不適切なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

MLIT · Japón27 nov 20141134761Años modelo 2010–2014Mostrado en japonés original · traducción pendienteVer detalles →
Juke I · 2010–2019
Juke I · 2010–2019
LlamadaCríticoMotorUK

Fuel may leak

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

DVSA · Reino Unido3 abr 2012R/2012/024Años modelo 2010–2012Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Sistema de alimentación de combustible, gasolina

Nissan está llevando a cabo una campaña de retirada de determinados vehículos de los modelos Juke, Infiniti QX e Infiniti M de los años 2011 y 2012. Es posible que los sensores de presión de combustible no se hayan apretado según las especificaciones correctas. Como consecuencia, el sensor de presión de combustible podría aflojarse debido al calor y a las vibraciones, lo que provocaría una fuga de combustible.

NHTSA · Estados Unidos24 feb 201212V069000Años modelo 2011–2012Traducido automáticamente · original: inglésVer detalles →
Juke I · 2010–2019
LlamadaCríticoMotorNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.

Transport Canada23 feb 20122012074Años modelo 2011–2012Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
LlamadaModeradoMotorUK

Engine push start switch may malfunction

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

DVSA · Reino Unido4 ago 2015R/2015/133Años modelo 2013–2014Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorEU

null The push engine start switch may remain in the pressed position and not return after switching the…

null The push engine start switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition, the emergency engine stop function may operate and cause the engine to stop unexpectedly.

Safety Gate · UE30 jun 2015A12/0850/15Años modelo 2013–2015Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorJP

始動装置

プッシュエンジンスタータスイッチを組み付けるイモビライザアンテナの成形条件が不適切なため、熱収縮により、当該プッシュエンジンスタータスイッチとの隙間が狭くなり、摺動抵抗が増加したものがある。そのため、そのまま使用を続けると、当該スイッチ操作時に押したまま戻らず、緊急停止操作と判定してエンジンを停止することがあり、最悪の場合、走行中にエンストするおそれがある。

MLIT · Japón25 jun 20151135950Años modelo 2013–2014Mostrado en japonés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorJP

エンジン本体

エンジンのタイミングチェーンにおいて、プレートを連結するピンの耐久性が不足しているため、表面処理が摩耗するものがある。そのまま使用を続けると、プレートのピン挿入穴が摩耗してタイミングチェーン全長が伸び、チェーンガイドと干渉して異音が発生し、最悪の場合、タイミングチェーンが破損してエンストに至るおそれがある。

MLIT · Japón25 jun 20151135940Años modelo 2010–2012Mostrado en japonés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorUK

Fuel may leak

On affected vehicles the fuel pressure sensor may not have been tightened to the correct specification. Heat and engine vibration may cause the sensor to loosen and in extreme cases allow fuel to leak.

DVSA · Reino Unido30 mar 2015R/2014/167Años modelo 2012–2014Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
LlamadaModeradoMotorUK

Engine may stall

The Turbocharger boost sensor bracket may separate from the air inlet tube. This means the boost pressure may be measured incorrectly and the engine warning lamp may be illuminated. During low-speed driving this could cause the engine to stall and not restart

DVSA · Reino Unido23 ene 2012R/2011/166Años modelo 2010–2011Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorNA

Engine

On certain vehicles, a weld at the boost sensor bracket may fail, allowing the bracket to separate from the air inlet tube. If this occurred, the engine would enter fail-safe driving mode, resulting in reduced motive power in which the vehicle could still be driven for short distances. Continued operation could cause the engine to stall which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the air inlet tube assembly.

Transport Canada12 dic 20112011431Años modelo 2011Mostrado en inglés original · traducción pendienteVer detalles →
Juke I · 2010–2019
LlamadaModeradoMotorNA

Engine and engine cooling:Engine:Gasoline:Turbo/supercharger

Nissan is recalling certain model year 2011 nissan juke vehicles manufactured from april 9, 2010, through may 12, 2011. The turbocharger boost sensor bracket may separate from the air inlet tube due to a defective weld.

NHTSA · Estados Unidos8 dic 201111V583000Años modelo 2011Mostrado en inglés original · traducción pendienteVer detalles →

Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).