Bollettino
Under certain driving situations, coolant leaks onto the fuel injectors on cylinder bank (5-8).
🔔 Crea un account gratuito per ricevere avvisi via e-mail su BMW M8 (tutte le generazioni)
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
Under certain driving situations, coolant leaks onto the fuel injectors on cylinder bank (5-8).
Under certain driving situations, coolant leaks onto the fuel injectors on cylinder bank (5-8).
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system(NVLD natural vacuum leak detection). For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5mm For: Model vehicles other that the ones listed above, or for EVAP faults related to a large leak, after confirming that the fuel filler cap is fitted properly, then, proceed to follow the corresponding test plan
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system (NVLD natural vacuum leak detection). For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5 mm.
Ritorno motore
One of the six engine oil pump mounting screws may not have been tightened with the correct torque.
Delivery stop: Oil pump screw connection
The NVLD limited emission related warranty for defects in materials or workmanship has been extended to 15 years/150,000 miles as determined from the original in-service date
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
Information updated about engine oil filter cap drain plug. When performing an engine oil service on vehicles equipped with a N63M, N63B or S63M engines; the ETK states to use "Set oil filter element" P/N 11 42 5 A33 C42 or P/N 11 42 5 A33 C43. The part numbers are not available at the moment.
When performing an engine oil service on vehicles equipped with a S63M engine the ETK states to use "Setoil filter element" P/N 11 42 5 A33 C43. P/N 11 42 5 A33 C43 is a new part number that was recently created without current parts availability. Until further notice ONLY use "Set oil filter element" P/N 11 42 7 848 321.
On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing.
B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. A manufacturing defect affecting the ignition coil insulation.
B58C AND B58M ENGINES ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: This Service Information Bulletin (Revision 1) replaces SI B11 01 20 dated February 2020. On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing (1).
Delivery Stop on certain Model Year 2019 and 2020 BMW vehicles that were produced between July 20 2018 and November 2 2019. There is a possibility of contamination in the engine.
HIGH ENGINE SPEED IMMEDIATELY AFTER STARTING. In rare circumstances after the engine is started with the Start-Stop button the engine speed may immediately increase to a high constant RPM (approximately 3000 rpm).
SERVICE ACTION: CHECK COOLANT LEVEL. The filling procedure at the factory could have set the engine coolant level in the expansion tank to below the minimum level.
SERVICE ACTION: CHECK COOLANT LEVEL. The filling procedure at the factory could have set the engine coolant level in the expansion tank to below the minimum level.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).