These vehicles may not comply with c.M.V.S.S. 301 - fuel system integrity. Some welds in the left rear quarter panel may have been missed during assembly. In the event of a vehicle crash, the vehicle sheet metal structure may not perform as designed. This could result in unexpected damage to the fuel tank or fuel lines and leakage of fuel. If there is a fuel leak and an ignition source, a fire could occur. Correction: Dealers will inspect for missing welds and, if necessary, place three welds between the involved panels.
Transport Canada30 ott 19961996173Anni modello 1997Mostrato in inglese originale · traduzione in attesaVedi dettagli →
During assembly of the left rear quarter panel, some welds were missed. This does not comply with the requirements of fmvss no. 301, "fuel system integrity."
NHTSA · Stati Uniti30 ott 199696V212000Anni modello 1997Mostrato in inglese originale · traduzione in attesaVedi dettagli →
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank leakage in the event of a rear impact collision. The fuel tank assemblies do not comply with fmvss no. 301, "fuel system integrity."
NHTSA · Stati Uniti1 lug 199494V122000Anni modello 1994Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · Stati Uniti19 ott 199292V150000Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Vehicles may have improperly torqued connections of the front fuel feed/return hoses to the fuel pipes at the body rail. A fitting may loosen enough to leak fuel into the underhood area, and, in the presence of an ignition source, a fire could result. Correction: Front fuel feed/return hose fittings will be properly torqued.
Transport Canada11 giu 19901990083Anni modello 1990Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On vehicles with quad 4 engines, the front fuel feed assembly could crack or separate at the coupling on the engine end of the assembly, allowing fuel to leak into the underhood area. This would create the possibility of an engine compartment fire. Correction: Front fuel feed hose assembly will be replaced on affected vehicles.
Transport Canada7 mar 19901990043Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · Stati Uniti5 mar 199090V042000Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Il sistema di alimentazione del carburante potrebbe presentare una perdita in corrispondenza del raccordo del tubo di alimentazione del carburante all'iniettore del corpo farfallato. Conseguenza del difetto: questa perdita potrebbe causare un incendio nel vano motore, che potrebbe propagarsi all'abitacolo e causare ustioni agli occupanti.
NHTSA · Stati Uniti29 mar 198585V034000Anni modello 1984Tradotto automaticamente · originale: ingleseVedi dettagli →
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
NHTSA · Stati Uniti8 mar 198282V021000Anni modello 1982Mostrato in inglese originale · traduzione in attesaVedi dettagli →
These vehicles do not comply with c.M.V.S.S. 301 - fuel system integrity. Rear compartment pan welds may not meet manufacturing standards. Correction: Dealers are to install rivets adjacent to the locations where suspect welds may have occurred.
Transport Canada20 lug 19941994117Anni modello 1994Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The vehicles were assembled with an incorrect suspension upper spring seat at the right-rear position. If the vehicle is involved in a rear impact accident, the right-hand rear wheel house flange could sever the fuel tank filler pipe and spill fuel.
NHTSA · Stati Uniti17 lug 199292V106000Anni modello 1992Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Note: Vehicles equipped with 2.3 litre engine. In sub zero temperatures, moisture from the crankcase ventilation system could cause ice buildup behind the throttle blade thereby preventing the throttle from returning to idle when the accerator pedal is released. This could result in loss of vehicle control. Correction: An engine ventilation kit will be installed on affected vehicles to prevent moisture accumulation in the crankcase.
Transport Canada12 dic 19911991174Anni modello 1988Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Certain vehicles may not comply with CMVSS 1103 - Exhaust Emissions. Cracks may develop in the casing of the integrated direct ignition coil. Correction: Ignition coils will be inspected and replaced if necessary.
Transport Canada5 mar 19911991037Anni modello 1988–1990Mostrato in inglese originale · traduzione in attesaVedi dettagli →
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. - mass airflow sensor failure - note : Vehicles with 3.0 litre and 3.8 litre engines.
Transport Canada27 gen 19871987007Anni modello 1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fuel hoses may be incorrectly positioned and contact the right front drive axle boot during vehicle operation. After a period of time, the rotating boot could wear a hole in the fuel hose, resulting in fule leakage.
NHTSA · Stati Uniti5 apr 197979V091000Anni modello 1980Mostrato in inglese originale · traduzione in attesaVedi dettagli →
These vehicles do not comply with c.M.V.S.S. 1101 - emission device. Unilingual unleaded fuel label.
Transport Canada29 set 19891989139Anni modello 1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).