Bollettino
Passenger fAirbag deactivation (PAD) indicator light illumination
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Mazda CX-9 (tutte le generazioni)
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
Passenger fAirbag deactivation (PAD) indicator light illumination
Mazda: Information provided regarding the indicator light illumination of the passenger airbag deactivation (pad). *pe
Mazda: On some vehicles, when a power plug with improper fabrication (such as a phone charger) is inserted into either of the accessory sockets (center and/or rear), the air bag warning light may illuminate. *pe
Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. pinched at the valve seat prevents the valve from closing completely. 2. The closed position of the EGR valve is learned improperly as it is not equipped with a position sensor. 3. While idling, the EGR gas improperly mixes in fresh air through the EGR valve that is not closed properly. 4. Misfire occurs. To eliminate this concern, the control software of the PCM has been modified to force the learning of the closed position of the EGR valve when a misfire is detected at idle
Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Refer to the vehicle owners manual for more details on proper seat warmer/seat ventilation operation.
2ND Row seat walk-in and recline lever usage
Third row seat head restraint is not upright - Some customers may complain about one or both third row seat head restraint(s) cannot be moved to the upright position, This may caused by improper fold position of the head restraint(s) when the seat back is folded down.
Second-row seat walk-in lever does not work. On some vehicles, The second-row seat back does not fold (B) or slide forward when the walk-in lever (A) is pulled up to access to the 3rd row seats. This concern may be caused by a disconnected walk-in lever cable. The design of the walk-in lever has been changed to reduce to force applied to the cable. Customer havingt this concern should have their vehicle repaired using the following repair procedure.
TAKATA recalls for Air bag
Third row seat head restraint is not upright
Stopper plates for air bag module connectors have been established as new service parts
Excessive operating noise when sliding front power seat(s)
All models - Stopper plates for air bag module coinnectors
Some customers may complain that their seat warmers do not turn on when the engine is restarted after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers automatically turned on when the engine was restarted. Customers in cold weather are more likely to complain about this if their vehicle is equipped with Mazda Mobile Start (MMS) because the MMS accessory instructions state the seat warmers WILL turn on when the engine is restarted. This information is incorrect for these vehicles. NOTE: The instructions in the vehicle owner's manual are correct.
Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.
Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.
Some customers may complain that the tachometer display in the Active Driving Display cannot be turned off using the MAZDA CONNECT setting menu since it has been removed by a CMU update. The concerns will be noticed after a CMU update from versions 58 to version 59. This is caused by the seat position memory control module storing the active driving display indication position, brightness level, and display information at the same time when the seat position is programmed. If the setting for the tachometer display was left ?ON? for the programmed position before the CMU update, the position memory control module still remembers the status and therefore the tachometer display remains.
Some vehicles may exhibit the driver and/or passenger side seat cushion trim coming out of the side cover, causing a poor appearance concern. This is due to the seat trim edge being cut too short. To eliminate this concern, the configuration of the seat trim will be improved.
If you encounter a 2016 cx-9 signature trim level vehicle (with nappa leather interior) where the front seat trim is loose / poor appearance, refer to the attached repair procedure to fix the vehicle. This concern may occur on either the driver and/or passenger side seat.Temporary countermeasure: Adhesive was applied to back of leather trim as of may 19, 2016 mass-production.Final countermeasure: A seat cushion trim edge shape change will be incorporated around aug. 1, 2016 mass-production.
Some vehicles may exhibit the driver and/or passenger side seat cushion trim coming out of the side cover, causing a poor appearance concern. This is due to the seat trim edge being cut too short. To eliminate this concern, the configuration of the seat trim will be improved.
Some customers may complain about one or both third row seat head restraint(s) cannot be moved to the upright position. This may be caused by improper fold position of the head restraint(s) when the seat back is folded down.
Seat belt retainer breaks. *nj
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).