I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
Alcuni clienti potrebbero notare l'accensione della spia SBS/SCBS, LAS/LDWS e/o HBC. Nel display centrale può inoltre comparire un messaggio di errore di sistema. DTC U3000:04-0A (Malfunzionamento interno della telecamera di rilevamento anteriore (FSC)). Il DTC U3000:04-0A (Malfunzionamento interno della telecamera di rilevamento anteriore (FSC)) è memorizzato nel modulo FSC e non può essere cancellato. Questo problema può essere causato da un guasto hardware di un dispositivo interno della FSC, che provoca il rilevamento di un malfunzionamento. Per eliminare il problema, il processo produttivo della FSC è stato modificato.
NHTSA · bollettino del costruttore10199641Anni modello 2021Tradotto automaticamente · originale: ingleseVedi dettagli →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · bollettino del costruttore10185813Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain about any of the following 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative.
NHTSA · bollettino del costruttore11039110Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicles may exhibit the check engine light ON with DTC P0300:00 (Random misfire detected) stored. This may be caused by a mis-detection of a misfire due to improper PCM control logic. To eliminate this concern, the PCM control logic has been modified.
NHTSA · bollettino del costruttore11012337Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may notice the charging lamp turns on while driving. Upon inspection, DTC P2502:00 PCM (Malfunction in voltage generated by generator) is stored in memory. This may be caused by resistance between the circuit board and ground. When high intensity electrical current passes through, the ground terminal position may not be sufficient enough. To eliminate this concern, the DC-DC converter control software has been modified. Additionally, the production procedure has been revised. The tightening torque for the ground terminal and circuit board was increased.
NHTSA · bollettino del costruttore11008418Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Alcuni clienti potrebbero notare l'accensione della spia del motore (check engine) al minimo, con il veicolo fermo, con il codice DTC P0300:00 memorizzato, con conseguente funzionamento irregolare del minore. P0300:00: Rilevata accensione casuale (misfire)
Questo problema è causato da un controllo motore non corretto nella gamma del minimo. Per eliminare il problema, il software di controllo del PCM è stato modificato.
NHTSA · bollettino del costruttore11008417Anni modello 2021Tradotto automaticamente · originale: ingleseVedi dettagli →
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
NHTSA · bollettino del costruttore10190951Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · bollettino del costruttore10180595Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · bollettino del costruttore10186918Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.
NHTSA · bollettino del costruttore10186257Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
NHTSA · bollettino del costruttore10144332Anni modello 2018Mostrato in inglese originale · traduzione in attesaVedi dettagli →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · bollettino del costruttore10105642Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · bollettino del costruttore10101468Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · bollettino del costruttore10091601Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · bollettino del costruttore10090667Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.
NHTSA · bollettino del costruttore10076685Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Mazda: There is condensation and fog in the front and rear combination lights. *rm
NHTSA · bollettino del costruttore10037655Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).