Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.
DVSA · Regno Unito3 apr 2012R/2012/024Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The engine ignition coil may not be to the correct specification. The internal electrical components of the coil may short circuit resulting in an engine misfire. In the worst case this short circuit may cause a fuse inside the Power Distribution Module (IPDM) to fail stopping power to the ignition relay. In this condition the engine may stall and prevent the customer from being able to restart the engine.
DVSA · Regno Unito22 feb 2016R/2016/008Anni modello 2015–2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.
DVSA · Regno Unito4 ago 2015R/2015/133Anni modello 2013–2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
null The push engine start switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition, the emergency engine stop function may operate and cause the engine to stop unexpectedly.
Safety Gate · UE30 giu 2015A12/0850/15Anni modello 2013–2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
It has been identified that it is possible that the contacts in engine control module (ECM) and ignition relay situationed in the Intelligent Power Distribution Module (IPDM) may become contaminated with silicon oxide due to the evaporating of the silicon from within the units. In extreme cases this could result in the stalling of the engine and the failure to restart the engine.
DVSA · Regno Unito29 nov 2010R/2010/185Anni modello 2004–2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Il metodo di fissaggio del serbatoio del carburante alla carrozzeria non è appropriato, per cui le tensioni si concentrano sugli angoli superiori. In alcuni casi, quando il serbatoio è sottoposto a ripetute dilatazioni e contrazioni dovute a effetti termici e simili, in questa zona possono formarsi crepe. Se si continua a usare il veicolo in tali condizioni, la cricca può propagarsi e, nel peggiore dei casi, attraversare la parete del serbatoio, con il rischio che il carburante trapeli quando il serbatoio è pieno.
MLIT · Giappone30 mar 20071118540Anni modello 1991–2000Tradotto automaticamente · originale: giapponeseVedi dettagli →
Alcuni sensori di rotazione del motore presentano un riempimento in resina interna non appropriato. Per effetto del calore del motore e di altri fattori, la saldatura della scheda di base può deformarsi, causando un cortocircuito nel circuito e l'impossibilità di trasmettere un segnale corretto. Di conseguenza, il motore può non avviarsi oppure, durante la marcia, arrestarsi e non poter più essere riavviato.
MLIT · Giappone30 ott 20031109950Anni modello 1998–2003Tradotto automaticamente · originale: giapponeseVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).