Lettura libera · account gratuito per contribuireErede di Anticars (2000)
NANHTSA · bollettino del costruttore11017500

Bollettini tecnici

Mostrato in inglese originale · traduzione in attesa

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Riguarda: Mercedes-Benz A-Class II (Anni modello 2007) · Mercedes-Benz A-Class III (Anni modello 2018) · Mercedes-Benz A-Class IV (W177) (Anni modello 2020) · Mercedes-Benz B-Class W246 (Anni modello 2018) · Mercedes-Benz B-Class W247 (Anni modello 2019) · Mercedes-Benz C-Class type 204 (Anni modello 2009–2011) · Mercedes-Benz C-Class W205 (Anni modello 2015–2020) · Mercedes-Benz C-Class W206 (Anni modello 2023–2024) · Mercedes-Benz CLK-Class C209 (Anni modello 2007–2008) · Mercedes-Benz CLS-Class C219 (Anni modello 2006) · Mercedes-Benz CLS-Class C218 (Anni modello 2011–2016) · Mercedes-Benz E-Class W211 (Anni modello 2006–2007) · Mercedes-Benz E-Class W212 (Anni modello 2012–2013) · Mercedes-Benz E-Class V213 (Anni modello 2018–2023) · Mercedes-Benz E-Class W214 (Anni modello 2025) · Mercedes-Benz EQC (Anni modello 2020–2021) · Mercedes-Benz EQE (Anni modello 2023) · Mercedes-Benz EQS (Anni modello 2022–2023) · Mercedes-Benz G-Class W463 (Anni modello 2010) · Mercedes-Benz G-Class (W465) (Anni modello 2025) · Mercedes-Benz GL-Class (Anni modello 2009) · Mercedes-Benz GLA II (Anni modello 2021–2024) · Mercedes-Benz GLB-Class I (Anni modello 2020) · Mercedes-Benz GLC I (Anni modello 2016–2019) · Mercedes-Benz GLC II (Anni modello 2024–2025) · Mercedes-Benz GLE-Class M-Class (W163) (Anni modello 2001) · Mercedes-Benz GLE-Class M-Class/GLE (W166/C292) (Anni modello 2015–2018) · Mercedes-Benz GLE-Class GLE (W167/C167) (Anni modello 2024–2025) · Mercedes-Benz GLK-Class (Anni modello 2009–2011) · Mercedes-Benz GT II (Anni modello 2023–2024) · Mercedes-Benz R-Class W251 (Anni modello 2007–2008) · Mercedes-Benz S-Class W220 (Anni modello 2001) · Mercedes-Benz S-Class W222 (Anni modello 2013–2017) · Mercedes-Benz S-Class VII (W223) (Anni modello 2021–2023) · Mercedes-Benz SL-Class R230 (Anni modello 2003) · Mercedes-Benz SL-Class R231 (Anni modello 2017) · Mercedes-Benz SL-Class R232 (Anni modello 2023–2024) · Mercedes-Benz SLK-Class R171 (Anni modello 2004–2009) · Mercedes-Benz SLK-Class R172 (Anni modello 2012–2017) · Mercedes-Benz X166 (Anni modello 2017)

Avviso ufficiale ↗

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).