무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Audi R8

2006–2024 · 1 세대 · 결함 1건 · 3개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
시장전체NA
공지심각엔진NA

공지

Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

NHTSA · 제조사 공지10123969연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지심각엔진NA

공지

Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.

NHTSA · 제조사 공지10122803연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulletin provides information for all gasoline engines when the MIL is on; DTC P240700 is stored - Fuel leak detection pump.

NHTSA · 제조사 공지11039214연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · 제조사 공지11034668연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulletin provides information regarding UV leak additive for finding oil leaks.

NHTSA · 제조사 공지11028398연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · 제조사 공지11025354연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This TSB provides information when the fuel tank cap seal is leaking, DTC P044200, P045600, and/or P00EF00 stored in ECM.

NHTSA · 제조사 공지11022688연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulleitn provides information regarding UV Leak additive for finding oil leaks.

NHTSA · 제조사 공지11022633연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This Pending Service Solution (PSS) requests that technicains enter a record in the PSS database in instances where the MIL is on, Eval leak detection pump circuit, DTC240700.

NHTSA · 제조사 공지11009316연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · 제조사 공지11005851연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · 제조사 공지11002215연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · 제조사 공지11002115연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This Pending Service Solution (PSS) requests that technicians enter a record in the PSS Database in instances where the MIL is on and DTC P240700 is stored; Evap leak detection pump circuit.

NHTSA · 제조사 공지10253248연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

This bulletin contains instructions for an oil leak that is due to excessive sealant used in a previous repair.

NHTSA · 제조사 공지10153121연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

On-Hoist Inspection Section: Removed "Perform a coolant reservoir cap pressure test via ELSA -> Enter VIN # -> Repair manual Engine -> 4-Cylinder Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III) -> 19 Cooling System -> Coolant System/Coolant -> Cooling System, Checking for Leaks -> Pressure Relief Valve in Cap, Checking. Only the procedure ?Pressure Relief Valve in Cap, Checking? should be performed in the document Cooling System, Checking for Leaks

NHTSA · 제조사 공지10120803연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · 제조사 공지10119945연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Supersedes Technical Service Bulletin Group 24 number 12-27 dated April 23, 2012. MIL is illuminated. Irregular engine performance. R8 Intake Air Hose leaking.

NHTSA · 제조사 공지10124951연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

NHTSA · 제조사 공지10124868연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · 제조사 공지10121324연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.

NHTSA · 제조사 공지11035854연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · 제조사 공지11035829연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · 제조사 공지11035828연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides informaiton when the engine is not running smoothly, misfiring.

NHTSA · 제조사 공지11034728연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · 제조사 공지11034657연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · 제조사 공지11027356연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).