공지
A faulty electric auxiliary heater may have been installed in the certain vehicles. This could result in thefailure of the electric auxiliary heater, utilized for the vehicle interior.
🔔 무료 계정을 만들고 BMW i5 (모든 세대) 이메일 알림 받기
기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.
A faulty electric auxiliary heater may have been installed in the certain vehicles. This could result in thefailure of the electric auxiliary heater, utilized for the vehicle interior.
A faulty electric auxiliary heater may have been installed in the certain vehicles. This could result in the failure of the electric auxiliary heater.
The coolant hose which runs from the combined charging unit (CCU) to the front electric motors housingmay develop a leak at the motor end of the hose.
A manufacturing defect in high-voltage cells of the high-voltage battery can result in electrolyte leakage which might result in a conductive connection with surrounding components. Depending on the contact resistance, a yellow or red Check Control message will then be displayed; it is permitted for you to continue driving, but this will result in a charging interruption during charging.
Charging sessions cannot be started or they are interrupted while using a Level 2 AC high-power chargingstation, or with a Level 3 DC charging station. Charging may start normally but can interrupt after some time. Level 2 (240 V) Flex Charger and Wall boxmay also be affected. The red or white LED is displayed on the high-voltage charging socket; however, no associated fault codesare stored.
Charging sessions cannot be started or they are interrupted while using a Level 2 AC high-power charging station, or with a Level 3 DC charging station. Charging may start normally but can interrupt after some time. Level 2 (240 V) Flex Charger and Wall box may also be affected. The red or white LED is displayed on the high-voltage charging socket; however, no associated fault codes are stored.
The customer states there is a Drivetrain Malfunction message displayed in the instrument cluster. In addition, the following fault memory entries are saved in the CCU (Combined Charging Unit) 0317F2 - High-voltage system, insulation fault detected: when switch contactors are closed. 0317F1 - High-voltage system, insulation resistance below warning threshold: when switch contactors are closed. The fault memory entries (isolation faults) can occur both individually and in combination and must be traced back to the eDrive motor based on the ISTA test procedure. If ISTA test procedure lists possible cause of fault as; A metal chip is found behind the brush module (between the brush module and the end shield of the electrical machine). Repair required. Refer to service solution no. 20000794435083 in Aftersales Information Research (AIR). Follow information in the Procedure section below.
RSU availability. It is possible the State of Health (SoH) of the high-voltage (HV) battery is displayed incorrectly to the customer. The value is continuously displayed as 100% regardless of the actual ageing of the HV battery.
The operating time value was written too high in the Storage Management Electronics (SME) during thehigh-voltage battery End Of Line (EOL) test. The excessive operating hours input results in a significant limitation in the charging capacity when vehicleis be charged with DC.
The customer states there is a Drivetrain Malfunction message displayed in the instrument cluster. In addition, the following fault memory entries are saved in the CCU (Combined Charging Unit) 0317F2 - High-voltage system, insulation fault detected: when switch contactors are closed. 0317F1 - High-voltage system, insulation resistance below warning threshold: when switch contactors are closed. The fault memory entries (isolation faults) can occur both individually and in combination and must be traced back to the eDrive motor based on the ISTA test procedure. If ISTA test procedure lists possible cause of fault as; A metal chip is found behind the brush module (between the brush module and the end shield of the electrical machine). Repair required. Refer to service solution no. 20000794435083 in Aftersales Information Research (AIR). Follow information in the Procedure section below.
This Informational Bulletin is intended as a guided work through process to address BEV/PHEV charging issues. The step-by-step guide will help walk you through the correct basic steps that should be followed when addressing and diagnosing battery electric vehicles (BEV) and plug in hybrid vehicles (PHEV) charging issues.
The customer states there is a Drivetrain Malfunction message displayed in the instrument cluster. In addition, the following fault memory entries are saved in the CCU (Combined Charging Unit) 0317F2 - High-voltage system, insulation fault detected: when switch contactors are closed. 0317F1 - High-voltage system, insulation resistance below warning threshold: when switch contactors are closed. The fault memory entries (isolation faults) can occur both individually and in combination and must be traced back to the eDrive motor based on the ISTA test procedure. If ISTA test procedure lists possible cause of fault as; A metal chip is found behind the brush module (between the brush module and the end shield of the electrical machine). Repair required. Refer to service solution no. 20000794435083 in Aftersales Information Research (AIR). Follow information in the Procedure section below.
Gen 5 BEV/PHEV vehicles may set the Combined Charging Unit (CCU) in programming abort due to nocommunication to the HV charge socket electronics.
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
Quality improvements and robustness measures are to be implemented on the affected vehicles via thissoftware update. The software update improves functions in the following areas of the head unit: 1. Bluetooth connection issues and Bluetooth malfunctions (disconnections) 2. Central display may remain black in rare cases 3. Personalization issues and the loss of normalization/sitting position 4. Missing Condition-Based Service (CBS) data
The purpose of this Service Bulletin (SIB) is informational regarding DC (direct current) charging complaints on Gen 5 Battery Electric Vehicles (BEV). It serves as a supporting argument and is intended to help distinguish between a standard designed function or component operation from an actual system fault in a DC charging customer complaint (i.e., DC Not charging or DC charging too slow. Helpful Tips and Tricks have been included on each topic within the document that can be used as reference to aid in the diagnosis or in understanding the system. The situation involves several possible causes: 1. Limitation of charging power by the charging station or charging app configuration. 2. Decreasing charging power at a very high state of charge (SoC). 3. Too frequent DC charging attempts within a short period of time. 4. The high-voltage battery is not at the ideal temperature. 5. Ageing of the high-voltage battery.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).