공지
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
🔔 무료 계정을 만들고 Buick Regal (모든 세대) 이메일 알림 받기
기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
This technical bulletin provides a procedure to repair the crankshaft positioning sensor wiring harness by installing a new wiring harness.
This technical bulletin provides repair information for tail lamp replacement to correct a custom concern of a cracked tail lamp and possible related water leak.
This Preliminary Information communication provides information to the technician about vehicles that have a no start or multiple messages on the Driver Information Center during cold weather. Technician will need to check the Vehicle Communication Interface Module label for Assembled in China. If the date is between 7/18/2014 and 8/3/2014, record the Station Identifier from the label and call General Motors Technical Assistance Center referencing this Preliminary Information for further assistance.
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
12313B - Special Coverage (revised warranty information). The chrome layer on the balance chain pins may wear, allowing the chain to stretch. This would cause an engine noise, and if left untreated, could cause the chain to break, leading to engine damage. In addition, the fuel pump plunger shaft seal may wear and allow fuel to leak into the crankcase, setting a P0172 DTC, and illuminating the Malfunction Indicator Light. This can cause engine run-on and/or the engine to run rough. If this condition occurs within the stated terms, dealers will replace the engine balance chain and the fuel pump.
12313 - Special Coverage. The chrome layer on the balance chain pins may wear, allowing the chain to stretch. This would cause an engine noise, and if left untreated, could cause the chain to break, leading to engine damage. In addition, the fuel pump plunger shaft seal may wear and allow fuel to leak into the crankcase, setting P0172 DTC, and illuminating the Malfunction Indicator Light. This can cause engine run-on and/or the engine to run rough. If this condition occurs within the stated terms, dealers will replace the engine balance chain and fuel pump.
12313A - Special Coverage (revised part information). The chrome layer on the balance chain pins may wear, allowing the chain to stretch. This would cause an engine noise, and if left untreated, could cause the chain to break, leading to engine damage. In addition, the fuel pump plunger shaft seal may wear and allow fuel to leak into the crankcase, setting P0172 DTC, and illuminating the Malfunction Indicator Light. This can cause engine run-on and/or the engine to run rough. If this condition occurs within the stated terms, dealers will replace the engine balance chain and fuel pump.
This Preliminary Information communication provides information to the technician about vehicles that have excessive oil consumption and/or that they have to add oil between oil changes. Technician should reprogram the Engine Control Module with the latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles. Technician should also inspect for any obvious oil leaks that may explain the oil consumption complaint, and repair as necessary.
This Preliminary Information communication provides information to the technician about vehicles that have excessive oil consumption and/or that they have to add oil between oil changes. Technician should reprogram the Engine Control Module with the latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles. Technician should also inspect for any obvious oil leaks that may explain the oil consumption complaint, and repair as necessary.
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P01285 and or P0171. Technician will need to use published Service Information diagnostics first. Technician will update the Engine Control Module with the latest calibration in Tis-2-Web if published Service Information diagnostics do not resolve the concern. If the calibration did not repair the concern inspect the engine for oil leaks and insure the oil fill cap is properly closed. Technician will also use the CH-44175-1 handheld tester to test the ethanol content of the fuel. Technician should also inspect for unmetered air/vacuum leaks by using the Evaporative Emissions System smoke machine to induce smoke into the engine, exhaust, and air intake system as outlined in the latest version of PIP4925. Technician should inspect the air filter condition to ensure that it is a factory filter and that none of the pleats are damaged and the inside of the air cleaner opening before the Mass Air Flow sensor for any sign of casting flash. If the concern is currently happening while at a hot idle, plug all vacuum lines.
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P01285 and or P0171. Technician will need to use published Service Information diagnostics first. Technician will update the Engine Control Module with the latest calibration in Tis-2-Web if published Service Information diagnostics do not resolve the concern. If the calibration did not repair the concern inspect the engine for oil leaks and insure the oil fill cap is properly closed. Technician will also use the CH-44175-1 handheld tester to test the ethanol content of the fuel. Technician should also inspect for unmetered air/vacuum leaks by using the Evaporative Emissions System smoke machine to induce smoke into the engine, exhaust, and air intake system as outlined in the latest version of PIP4925. Technician should inspect the air filter condition to ensure that it is a factory filter and that none of the pleats are damaged and the inside of the air cleaner opening before the Mass Air Flow sensor for any sign of casting flash. If the concern is currently happening while at a hot idle, plug all vacuum lines.
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
12238a - service update (revised service procedure). The generator control module (gcm) may not function properly, resulting in the gradual loss of battery charge, illumination of the mil, and eventual engine stall or no start condition. Dealers are to inspect and replace the gcm, if necessary.
12238 - service update. The generator control module (gcm) may not function properly, resulting in the gradual loss of battery charge, illumination of the mil, and eventual engine stall or no start condition. Dealers are to inspect and replace the gcm, if necessary.
General motors: Due to the parasitic drain/discharge on 2011 vehicles and trucks, a no crank/no start and dead battery would occur. Cadillac sts and chevrolet volt not included. *pe
Gm: See document search button for owner letter. 2011 lacrosse, equinox, terrain. The malfunction light will come on along with, rough idle, poor driveability, and/or possible stalling at low throttle opening. This is due to a problem with the camshaft. *rm updated 10/4/11. *pe updated 12/5/11. *pe
이 사전 정보는 DTC(고장 코드)가 없는 상태에서 텔레매틱 모듈의 GPS 문제를 진단하는 방법을 현장에 안내합니다.
이 예비 정보는 DTC(고장 진단 코드)가 없는 상태에서 텔레매틱 모듈의 GPS 문제를 진단하는 방법을 현장에 전달하기 위한 것입니다.
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's Wait, I need to correct myself: the text above is not what you sent. Your message is the English sentence: "This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's." Here is the translation: 이 예비 정보(Preliminary information)는 DTC(고장 진단 코드)가 없는 상태에서 텔레매틱스 모듈의 GPS 문제를 진단하는 방법을 현장에 전달하기 위한 것이다.
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
Ignition를 껐다 켠 후 Driver Information Center에 "Transport Mode On" 메시지가 표시될 수 있습니다.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).