에어백:전면:센서/제어 모듈-비활성
일부 승용차에서는 통합 에어백 모니터(IABM)가 물이나 기타 액체에 오염될 수 있으며, 내부 전기 단락이 발생할 수 있습니다.
🔔 무료 계정을 만들고 Ford Escort (모든 세대) 이메일 알림 받기
일부 승용차에서는 통합 에어백 모니터(IABM)가 물이나 기타 액체에 오염될 수 있으며, 내부 전기 단락이 발생할 수 있습니다.
운전석 에어백 모듈의 인플레이터 캐니스터가 용접이 불충분하게 되어 있을 수 있습니다.
차량 설명: TRW 안전벨트 버클 어셈블리가 장착된 승용차, 경트럭, 스포츠유틸리티차량(SUV) 및 미니밴. 이러한 안전벨트 어셈블리의 버클 베이스는 열처리가 제대로 되지 않아, 연방 자동차 안전 기준 제209호 "안전벨트 어셈블리"의 하중 지지 요건을 충족하지 못합니다.
정전기 방전이 에어백 점화기를 통해 발생하여 조수석 에어백이 예기치 않게 전개되는 현상.
The two bolts that attach the passenger side air bag supplemental restraint system module to the instrument panel may be missing on some vehicles. If the vehicle is involved in a collision, the module could come out of the instrument panel, which could potentially result in personal injury. Correction: Mounting bolts will be installed and torqued to proper specification.
Two bolts that attach the passenger side air bag supplemental restraint system module to the instrument panel are missing. In the event of a frontal impact, the module can come out of the instrument panel.
The lock plate of the driver side inboard seat track adjusters were manufactured with an unauthorized modification to the fabrication process which causes the seat not to fully engage in certain seating positions near the mid-point of the seat track travel.
The driver side inboard seat track may not fully engage the seat adjuster in certain seating positions near the mid-point of the seat track travel. If this occurs, the seat may move in the event of a crash possibly resulting in reduced occupant protection. Correction: Driver side inboard seat track will be replaced on affected vehicles.
The forward outboard pedestal of the seat track of the driver's seat may be susceptible to fatigue fracture. Fracture of this pedestal would permit a limited degree of rocking motion of the driver's seat assembly upon acceleration or deceleration. Breakage of the bracket could, potentially, affect the driver's control of the vehicle and result in an accident. Correction: A reinforcement will be installed on the seat track or the seat track will be replaced if fractured.
The forward outboard pedestal of the seat track of driver's seat may be susceptible to fatigue fracture.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
The rear seat belt retractors may allow twisted webbing to enter the retractor housing. Twisted webbing may wedge between the retractor spool and housing producing a jammed retractor condition which interfered with webbing retraction and withdrawal.
Rear seat belt retractors may allow twisted webbing to enter the retractor housing and jam the retractor. Consequence of defect: A jammed retractor would interfere with webbing retraction and withdrawal. This will discourage seat belt usage.
On vehicles with optional front seat recliners, the upper shoulder screw that attaches the driver's seat back frame to the recliner mechanism may be susceptible to fatigue fracture. If fatigue fracture of the recliner upper attachment screw were to occur on the driver's seat, the seat back could rotate rearward to a near horizontal position without warning potentially affecting the driver's control of the vehicle.
Screw that connects the seat back frame to the recliner mechanism may break.
When severely loaded by a frontal impact, the seat belt webbing may contact the leading edge of the front seat-back stell reinforcement plates. This may cause the seat belt webbing to be abraded, cut or completely severed, thereby significantly increasing the risk of serious personal injuries.
Seat frame structure could sever front seat belts if vehicle is involved in an accident, depending on force of impact.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
The portion of the roof above frame (rail) to which the shoulder belt is anchored may have a slot that can compromise the strength of the shoulder belt anchor under certain severe loads. (the suspect area is not visible.) consequently, some vehicles included in this recall may not meet the 3000 pound anchorage strength requirements of federal motor vehicle safety standard 210, "seat belt assembly anchorages".
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).