어떤 점화 스위치에서는 일부 접점에 그리스가 과도하게 도포되었습니다.
일부 점화 스위치에서는 일부 접점 부위에 그리스가 과도하게 도포되었습니다. 이러한 조건에서 사용되는 차량의 경우, 그리스가 탄화되어 화재 위험이 높아질 수 있습니다.
🔔 무료 계정을 만들고 Mazda 626 (모든 세대) 이메일 알림 받기
일부 점화 스위치에서는 일부 접점 부위에 그리스가 과도하게 도포되었습니다. 이러한 조건에서 사용되는 차량의 경우, 그리스가 탄화되어 화재 위험이 높아질 수 있습니다.
over the time 대신 자연스럽게: 시간이 지나면서 점화 스위치 내부의 접점이 탄화되어 전기가 통하기 쉬운 상태가 될 수 있습니다. 그 결과 점화 스위치가 과열되어 화재 위험으로 이어질 수 있습니다.
점화 스위치의 접점 사이에 탄화된 그리스가 쌓여 스위치 내부의 절연 성능을 저하시킬 수 있습니다. 이러한 상태에서는 스위치가 열을 발생시켜 연기가 나고, 최악의 경우 화재로 이어질 수 있습니다.
전기 접점에 남은 과잉 그리스가 탄화(카본화)되면서 점화 스위치 내부에 단락이 발생함.
Fuel tank fixing band retention is not sufficient, allowing the band to rub against the fuel tank by vehicle vibrations.
The camshaft drive belt may break and cause the engine to stop suddenly.
On certain vehicles, an external spring in the timing belt auto tensioner may break. The broken spring may get caught in the timing belt, resulting in possible engine stalling. Correction: Dealers will inspect the tensioner on affected vehicles and replace if necessary.
Vehicle description: Passenger vehicles. An external spring in the timing belt tensioner could break.
Certain vehicles do not comply with the requirements of CMVSS. 1103 - Exhaust Emissions. The average CO of the subject vehicles may exceed the standard due to insufficient robustness of emission control logic, and calibration of emission parts with extended usage. Correction: Dealers will install an engine intake kit, which will allow additional air to enter the engine, improving combustion efficiency and lowering the levels of carbon monoxide.
Certain vehicles do not comply with the requirements of CMVSS 1105 - Evaporative Emissions. Fuel vapour may leak from between the fuel cap and the fuel filler pipe. The gap could be generated by improper dimensions between the top ends of the inner and outer pipe of the fuel filler pipe. In some cases, raw fuel would be released into the atmosphere. Correction: Dealers will install a modified fuel cap o-ring.
On certain vehicles, an external spring in the timing belt auto tensioner may break. The broken spring may get caught in the timing belt, resulting in possible engine stalling. Correction: Vehicles will be inspected and affected tensioners will be replaced.
Vehicle description: Passenger vehicles. An external spring in the timing belt tensioner can break and get caught in the timing belt.
The engine may stop while driving and can not be restarted. The strength of the inner part of the spill valve on the fuel injection pump is insufficient and may fail as a result of repeated injection pressure. As a result fuel can not be injected into the combustion chambers.
Note: Vehicles equipped with 2.0 litre engine. The powertrain control module (pcm) may trigger a shift in air-fuel ratio to an over-lean condition resulting in an engine stall. This could lead to loss of vehicle control and a possible vehicle crash. Correction: Pcm will be reprogrammed with the correct engine control logic.
Vehicle description: Passenger vehicles. Due to a programming error, the powertrain control module (pcm) installed can, under certain driving conditions, trigger a shift in air-fuel ratio to an overlean condition.
At ambient temperatures below -18 degrees celsius, frost may accumulate within the throttle body under conditions of extended constant speed operation. This could result in a heavy accelerator pedal and cause uneven throttle valve return. Correction: The single stage engine coolant thermostat will be replaced with a dual stage thermostat equipped with a subvalve to increase the temperature within the throttle body. V.I.N. Range: Jm1gd3120j1500014 to jm1gd2226j1573252.
These vehicles may not comply with c.M.V.S.S. 124 -accelerator control systems. Vehicles equipped with electronic fuel injection.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).