무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mazda MX-30

2020– · 1 세대 · 결함 1건 · 4개 시장
세대
모든 세대MX-302020–19123

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
공지보통차체NA

공지

## 설명 일부 고객은 리모컨 송신기로 도어 잠금 및 잠금 해제가 정상적으로 작동하더라도 다음 증상 중 한 가지 또는 두 가지를 겪을 수 있습니다. 증상 1: 비가 오거나 세차한 후 앞도어 아웃사이드 핸들의 터치 센서가 도어를 잠그지 못하지만 잠금 해제는 가능합니다. 증상 2: 앞도어 아웃사이드 핸들의 터치 센서가 도어를 잠금 해제하지 못합니다. 도어 아웃사이드 핸들 터치 센서 잠금(1) / 잠금 해제(2) 참고: 아래에 설명된 특정 작업 후에 문제가 발생하면 TSB 09-046/22(특정 작업 후 도어 아웃사이드 핸들 터치 센서가 잠기지 않고 잠금 해제되지 않음)를 참조하십시오. 1. [MX-30] 실내 사전 공조 또는 비상등을 약 15분간 사용한 후 2. [MAZDA3 및 CX-30] 비상등을 약 15분간 사용한 후 3. [MAZDA3, CX-30 및 MX-30] 두 개의 터치 센서를 동시에 터치한 경우 원인 1(증상 1의 원인): 아웃사이드 핸들의 터치 센서 주변에 물이 고여 정전식 센서의 감도가 일시적으로 저하될 수 있습니다. 또한 차량 세차 중 세차용 거품이 아웃사이드 핸들 내부로 들어가면 거품이 터치 센서의 감지를 방해할 수 있습니다. 마쓰다는 이 문제에 대한 양산 변경을 계속 진행하고 있습니다. 원인 2(증상 2의 원인): 생산 공정에서의 불량 납땜이 터치 센서의 감지를 방해할 수 있습니다. 이 문제를 해결하기 위해 생산 공정이 변경되었습니다. 이 문제를 겪는 고객의 차량은 다음 수리 절차에 따라 수리해야 합니다. ## 수리 절차 1. 고객 불만 사항을 확인합니다. 2. 발생한 증상에 따라 차량을 수리합니다. - 증상 1: 아래의 "터치 센서 방수 처리 절차"를 따라 터치 센서를 방수 처리합니다. - 증상 2: MGSS의 지침에 따라 앞 아웃사이드 핸들을 개선된 제품으로 교체합니다. - Mazda3 (앞 아웃사이드 핸들 탈거/장착) - CX-30 (앞 아웃사이드 핸들 탈거/장착) - MX-30 (앞 아웃사이드 핸들 탈거/장착) 두 가지 증상이 모두 발생한 경우: 앞 아웃사이드 핸들을 개선된 제품으로 교체하고, 아래의 "터치 센서 방수 처리 절차"를 따라 터치 센서를 방수 처리합니다. 참고: 문제가 없는 다른 쪽 앞 아웃사이드 핸들은 수리하지 마십시오. 3. 새로운 아웃사이드 핸들로 도어가 올바르게 잠기고 잠금 해제되는지 확인하여 수리를 검증합니다.

NHTSA · 제조사 공지11030603연식 2022자동 번역 · 원문: 영어자세히 보기 →
공지보통차체NA

공지

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · 제조사 공지10252505연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified

NHTSA · 제조사 공지10244579연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified.

NHTSA · 제조사 공지10233659연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · 제조사 공지10226892연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.

NHTSA · 제조사 공지11016214연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

NHTSA · 제조사 공지11009639연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

NHTSA · 제조사 공지11007022연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · 제조사 공지10254183연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may exhibit a rattle noise near the drivers and/or passengers head rests at the B-pillar area while driving on rough roads. This is caused by an interference between the rear end of the front door glass run-channel and the front end of rear sash molding.

NHTSA · 제조사 공지10252373연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · 제조사 공지10246137연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · 제조사 공지10240403연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.

NHTSA · 제조사 공지10240399연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may exhibit the warning message "Ultrasonic Sensor Malfunction" in the instrument cluster and the following DTC(s) stored after replacing the front and/or rear ultrasonic sensor(s) during body or paint repair.

NHTSA · 제조사 공지10238672연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

NHTSA · 제조사 공지10233683연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

NHTSA · 제조사 공지10232303연식 2022–2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. - Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. - Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. - Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. - Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified.

NHTSA · 제조사 공지10226856연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may complain about any of the following: * Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. * Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF * MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\"

NHTSA · 제조사 공지10225727연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

NHTSA · 제조사 공지10225724연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may experience the MyMazda App not communicating to the vehicle properly which may result in the condition monitor information is not refreshed or remote door lock/unlock not functioning. This is caused by a failure in communication between the telematics communication unit and the MyMazda App. To correct this issue, the control software of the telematics communication unit has been modified.

NHTSA · 제조사 공지10222572연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may exhibit the fuel-filler or charge lid opening unintentionally when unlocking the front doors using the door lock switch, the touch sensor on the outer door handle, or the remote transmitter. This is caused by a mechanical issue at the actuator of the fuel-filler/charge lid (when the fuel filler/charge lid is pushed hard, the guide pin in the actuator comes off). To eliminate this concern, the durability of the guide pin in the actuator has been improved.

NHTSA · 제조사 공지10222571연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector. Some Mazda3, CX-30 and MX-30 customers may complain that the vehicle door locking system does not work when the door lock switch on the liftgate interior trim is pressed. DTC B11C4:23 (BCM - liftgate lock switch circuit malfunction) may be stored. This may be caused during a high pressure car wash and/or condensation. Water may enter through the rear center brand emblem base component and drip onto the switch connector causing corrosion. The rusted connector may also cause a battery drain. To eliminate this concern, the rear center brand emblem base has been modified to prevent water entry (Mazda3) and the rear harness has been modified to prevent water infiltration (Mazda3, CX-30 and MX-30).

NHTSA · 제조사 공지10218727연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may experience the MyMazda App not communicating to the vehicle properly which may result in the condition monitor information is not refreshed or remote door lock/unlock not functioning. This is caused by a failure in communication between the telematics communication unit and the MyMazda App. To correct this issue, the control software of the telematics communication unit has been modified.

NHTSA · 제조사 공지10218733연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some vehicles may exhibit a rattle noise near the drivers and/or passengers head rests at the B-pillar area while driving on rough roads. This is caused by an interference between the rear end of the front door glass run-channel and the front end of rear sash molding. To eliminate this concern, the front end of the rear sash molding has been modified to reduce the contact friction with the front door glass run channel.

NHTSA · 제조사 공지10218736연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미차체NA

공지

Some customers may complain about any of the following: - Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. - Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF - MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Confirm the customer's phone and vehicle have good to strong reception during the concern as shown in the table below. - If the reception is weak, move the vehicle to a location where the reception is good to strong as shown in the table, then try to get the Authorization Code and/or operate the remote functions before proceeding to the Repair Procedure if there is still an issue. - If the reception is good to strong, proceed to the Repair Procedure.

NHTSA · 제조사 공지10219228연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).