좌석 및 안전벨트
노출된 햇빛에 장시간 노출되면 잠금 바를 고정하는 앞좌석 안전벨트 혀(tongue) 조립체의 플라스틱 슬리브가 열화되어 위치가 이탈할 수 있습니다. 이로 인해 혀 부분이 안전벨트 웨빙에서 분리될 수 있으며, 그 경우 탑승자가 안전벨트를 사용할 수 없게 될 가능성이 있습니다. 정정: 차주에게 이러한 상태의 안전벨트를 포드(Ford)가 수리해 준다는 사실이 안내될 예정입니다.
🔔 무료 계정을 만들고 Mercury Capri (모든 세대) 이메일 알림 받기
노출된 햇빛에 장시간 노출되면 잠금 바를 고정하는 앞좌석 안전벨트 혀(tongue) 조립체의 플라스틱 슬리브가 열화되어 위치가 이탈할 수 있습니다. 이로 인해 혀 부분이 안전벨트 웨빙에서 분리될 수 있으며, 그 경우 탑승자가 안전벨트를 사용할 수 없게 될 가능성이 있습니다. 정정: 차주에게 이러한 상태의 안전벨트를 포드(Ford)가 수리해 준다는 사실이 안내될 예정입니다.
The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.
에어백 모듈이 고온 환경 성능에 대한 Ford 사양을 충족하지 못합니다.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
These vehicles do not comply with cmvss 209 - seat belt assemblies.
The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.
Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).