Boletim
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Audi S4 (todas as gerações)
Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost.
An oil filter that is too short is installed. The oil filter must be 155 mm.
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost.
An oil filter that is too short is installed. The oil filter must be 155 mm.
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost.
An oil filter that is too short is installed. The oil filter must be 155 mm.
This bulletin contains instructions for using the UV additive to find engine oil leaks.
This bulletin contains instructions for using the UV additive to find engine oil leaks.
Audi: The oil filter, for some vehicles, are too short, (should be 155 (=/-1) mm long) for installation and drain flap, in oil filter housing, can not completely close causing lost of oil pressure. Model 2013 a6, a7, s4, s5, s5 cab, q7, q5. *pe
Audi: The coolant pump is leaking or the engine is overheating without a leak. *rm
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
This bulletin provides information for when there is an Engine Start system warning, or Power Unit start system warning, B200047.
This bulletin provides information on checking for debris when replacing an engine.
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
This bulletin provides information to address the message "Switch off the engine and check coolant" with the DTC P000000
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).