Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

BMW Série 7 E32

1986–1994 · 5 defeitos documentados · 4 mercados
Ano do modelo
MercadoTodosNA
RecallCríticoMotorNA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

Transport Canada30 de mai. de 19941994096Anos-modelo 1989–1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallCríticoMotorNA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · Estados Unidos11 de abr. de 199494V066000Anos-modelo 1989–1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · Estados Unidos4 de ago. de 199898V178000Anos-modelo 1988–1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine

On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.

Transport Canada9 de out. de 19971997173Anos-modelo 1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · Estados Unidos19 de ago. de 199797V131000Anos-modelo 1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

Transport Canada25 de abr. de 19941994081Anos-modelo 1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · Estados Unidos3 de jan. de 199494V022000Anos-modelo 1993Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

Transport Canada13 de out. de 19921992129Anos-modelo 1991Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · Estados Unidos10 de jul. de 199292V101000Anos-modelo 1991Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

Transport Canada2 de mai. de 19891989063Anos-modelo 1988–1989Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

Transport Canada2 de mai. de 19891989062Anos-modelo 1988–1989Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

Transport Canada6 de abr. de 19891989046Anos-modelo 1988–1989Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).