Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

BuickBuick Rainier

2003–2007 · 1 gerações · 12 defeitos documentados · 1 mercados
Gerações
Todas as geraçõesRainier2003–20071212361

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

Ano do modelo
MercadoTodosNA
BoletimModeradoElétricaNA

Boletim

Esta comunicação de Informação Preliminar fornece ao técnico informações sobre veículos com um problema intermitente de não girar o motor, não dar partida ou falha na partida (start stall), com a luz de segurança acesa. O técnico pode encontrar os Códigos de Diagnóstico de Falha B3055, B3

NHTSA · boletim do fabricante11039894Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoElétricaNA

Boletim

Esta comunicação de Informações Preliminares fornece ao técnico informações sobre veículos que apresentam um problema intermitente de não dar partida, não pegar motor ou morrer ao pegar, com a luz de segurança acesa. O técnico pode encontrar os Códigos de Diagnóstico de Falha B3055, B3060, B3935, C0750, C0755, C0760, C0765 e/ou C0775.

NHTSA · boletim do fabricante11021792Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoElétricaNA

Boletim

Esta comunicação de Informações Preliminares fornece informações ao técnico sobre veículos que apresentam uma condição intermitente de não dar partida, não ligar ou parar durante a partida, com a luz de segurança acesa. O técnico pode encontrar os Códigos de Diagnóstico de Falha B3055, B3060 e/ou B3935. O técnico não deve substituir nenhuma peça para este problema. Se não for possível reproduzir a condição, pergunte ao cliente se ele usa algum dispositivo de Identificação por Radiofrequência (RFID) quando o problema estiver presente. A concessionária também deve orientar seus clientes para a seção apropriada dos Manuais do Proprietário que indica que o dispositivo está em conformidade.

NHTSA · boletim do fabricante11007196Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

NHTSA · boletim do fabricante10237659Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

NHTSA · boletim do fabricante10201252Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

NHTSA · boletim do fabricante10201176Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

NHTSA · boletim do fabricante10178384Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

NHTSA · boletim do fabricante10174861Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10114354Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10113935Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10113191Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10113120Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10112436Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10111986Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

This preliminary information communication provides information to the technician that some vehicles may have a service engine soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 pounds per square inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management valve lifter oil manifold diagnosis and testing in service information. If it isolates a concern with the valve lifter oil manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 full size truck/suv or a 2007-2009 chevrolet tahoe with the police package reprogram the engine control module. On the 2008-2009 pontiac g8, 2010-2011 camaro, and 2007-2010 full size trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the ls4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · boletim do fabricante10094982Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

Diagnostic information on engine oil leak from rear of crankshaft. *tt 05-06-01*022 supplement - crankshaft oil leak repair instrumentions. *tt

NHTSA · boletim do fabricante10017385Anos-modelo 2005Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

Service engine soon light due a diagnostic trouble code p0606 diagnostic trouble code, operate in reduced engine power mode, and potentially stall. *tt

NHTSA · boletim do fabricante10017230Anos-modelo 2004Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

Este boletim de serviço fornece informações sobre alguns veículos que podem balançar ou se mover ligeiramente para frente ou para trás enquanto estão em Park (Estacionamento) na partida após um longo período de resfriamento (cold soak). Essa condição pode ser acompanhada por um ruído de batida metálica (clunk). Trata-se de um movimento leve, que é mais frequentemente percebido visualmente do que sentido, quando observado de fora do veículo e ao usar o recurso de partida automática, se equipado.

NHTSA · boletim do fabricante11009088Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimLeveElétricaNA

Boletim

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · boletim do fabricante10237387Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

NHTSA · boletim do fabricante10174304Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

NHTSA · boletim do fabricante10159575Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

NHTSA · boletim do fabricante10154629Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues.

NHTSA · boletim do fabricante10140364Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.

NHTSA · boletim do fabricante10139415Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveElétricaNA

Boletim

This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

NHTSA · boletim do fabricante10139200Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
Mais antigos →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).