Airbags: Frontal: Sensor/módulo de controlo - inativo
Em certos veículos de passageiros, o monitor integrado do airbag (IABM) pode estar contaminado com água ou outros líquidos e pode sofrer curtos-circuitos internos elétricos.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Ford Escort (todas as gerações)
Em certos veículos de passageiros, o monitor integrado do airbag (IABM) pode estar contaminado com água ou outros líquidos e pode sofrer curtos-circuitos internos elétricos.
O módulo do airbag do lado do motorista pode ter um cilindro inflador com solda inadequada.
Descrição do veículo: Veículos de passageiros, camiões ligeiros, veículos utilitários desportivos e mini-carrinhas equipadas com conjuntos de fivela de cinto de segurança TRW. A base da fivela destes conjuntos de cintos de segurança não foi devidamente tratada termicamente e, por isso, não cumpre o requisito de suporte da norma federal de segurança automóvel nº 209, "conjuntos de cinto de segurança".
Implantação inesperada do airbag do passageiro devido a uma descarga eletrostática através do acionador (igniter) do airbag.
The two bolts that attach the passenger side air bag supplemental restraint system module to the instrument panel may be missing on some vehicles. If the vehicle is involved in a collision, the module could come out of the instrument panel, which could potentially result in personal injury. Correction: Mounting bolts will be installed and torqued to proper specification.
Two bolts that attach the passenger side air bag supplemental restraint system module to the instrument panel are missing. In the event of a frontal impact, the module can come out of the instrument panel.
The lock plate of the driver side inboard seat track adjusters were manufactured with an unauthorized modification to the fabrication process which causes the seat not to fully engage in certain seating positions near the mid-point of the seat track travel.
The driver side inboard seat track may not fully engage the seat adjuster in certain seating positions near the mid-point of the seat track travel. If this occurs, the seat may move in the event of a crash possibly resulting in reduced occupant protection. Correction: Driver side inboard seat track will be replaced on affected vehicles.
O pedestal exterior dianteiro da trilha do banco do condutor pode ser suscetível a fraturas por fadiga. A fratura deste pedestal permitiria um grau limitado de movimento de balanço do conjunto do banco do condutor durante a aceleração ou desaceleração. A rutura do suporte poderia, potencialmente, afetar o controlo do condutor sobre o veículo e resultar num acidente. Correção: Será instalado um reforço na pista do banco ou a trilha do banco será substituída se estiver fraturada.
O pedestal dianteiro externo do trilho do assento do motorista pode ser suscetível a fratura por fadiga.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
The rear seat belt retractors may allow twisted webbing to enter the retractor housing. Twisted webbing may wedge between the retractor spool and housing producing a jammed retractor condition which interfered with webbing retraction and withdrawal.
Rear seat belt retractors may allow twisted webbing to enter the retractor housing and jam the retractor. Consequence of defect: A jammed retractor would interfere with webbing retraction and withdrawal. This will discourage seat belt usage.
On vehicles with optional front seat recliners, the upper shoulder screw that attaches the driver's seat back frame to the recliner mechanism may be susceptible to fatigue fracture. If fatigue fracture of the recliner upper attachment screw were to occur on the driver's seat, the seat back could rotate rearward to a near horizontal position without warning potentially affecting the driver's control of the vehicle.
Screw that connects the seat back frame to the recliner mechanism may break.
When severely loaded by a frontal impact, the seat belt webbing may contact the leading edge of the front seat-back stell reinforcement plates. This may cause the seat belt webbing to be abraded, cut or completely severed, thereby significantly increasing the risk of serious personal injuries.
Seat frame structure could sever front seat belts if vehicle is involved in an accident, depending on force of impact.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
The portion of the roof above frame (rail) to which the shoulder belt is anchored may have a slot that can compromise the strength of the shoulder belt anchor under certain severe loads. (the suspect area is not visible.) consequently, some vehicles included in this recall may not meet the 3000 pound anchorage strength requirements of federal motor vehicle safety standard 210, "seat belt assembly anchorages".
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).