Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings
Fuel filter may not meet the specification concerning leakage criteria due to low temperature during the gluing process.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Saab 900 (todas as gerações)
Fuel filter may not meet the specification concerning leakage criteria due to low temperature during the gluing process.
On certain Saab 900S and 900 turbo, the fuel hose between the pressure regulator and the injector fuel rail may rupture due to stress resulting in a fuel leak and possible fire. Correction: A new plastic fuel hose with an outer casing of rubber will be installed.
The fuel hose between the pressure regulator and the injector fuel rail may rupture due to stress.
The flexible fuel hose located between the injector fuel rail and the fuel pressure regulator may rupture. The hose may have been turned out of its correct position when being tightened during final vehicle assembly. A sharp bend or twist in the hose near one of its end fittings could lead to hose rupture with fuel leakage creating a possible fire hazard. 16 valve turbo vehicles.
The flexible fuel hose may have been turned out of its normal position and have a sharp bend or twist near one of its fittings. Consequence of defect: This could lead to hose rupture, fuel leakage, and possibly a fire.
Existe a possibilidade de que o colar de montagem da bomba elétrica de combustível, submerso no combustível, possa descolar-se parcialmente do topo do depósito e causar uma fuga de combustível.
原動機のウォータポンプのベアリングの一部に加工不良のものがあり、そのままの状態 で使用を続けると、当該ベアリングのシールが損傷し、最悪の場合、冷却水が漏れオーバ ーヒートに至るおそれがある。
原動機において、タイミングベルトのベルトテンショナのブラケット固定用ボルトの強 度が不足しているため、そのままの状態で使用を続けると、ベルトテンショナが偏芯し、 タイミングベルトが損傷又はカムスプロケットが破損し、最悪の場合、ベルトが外れて原 動機が停止するおそれがある。
原動機の回転数を制御するスロットルレバーのブッシュ(穴の内側にはめ込む円筒形の軸 受)の表面処理が不適切なため、そのままに状態で使用を続けると、当該ブッシュが腐食 し、円滑なスロットルの動きが妨げられ、最悪の場合、エンジン回転が下がらないおそれ がある。
Note: Vehicles with 4-cylinder engines. The zinc-coated throttle control lever bushings in the throttle housing may corrode, causing the throttle lever to bind. This could result in the throttle plate not returning to the closed position when the accelerator pedal is released and a subsequent loss of throttle control. Correction: Zinc-coated throttle lever bushing in the throttle housing will be replaced with a nickel-coated bushing and bolt.
Binding of the throttle lever may occur due to the possibility of white corrosion.
原動機のウォーターポンププーリについて、溶接方式のプーリに強度不足のものがあり 、そのままの状態で使用を続けると溶接部に亀裂が発生し、最悪の場合、原動機が停止す るおそれがある。
Note: Vehicles with 2.3l engines and bosch motronic 2.10.3 engine control modules. Defect: It is possible that an internal voltage drop can result in an intermittent fluctuating idle. This up-down idling may occur during the first 10-30 seconds after restarting the vehicle with a warm engine. Correction: Affected engine control modules will be replaced.
Poor electrical connection at the fuel gauge transmitter may result in a stoppage of the fuel pump and engine stalling. In extreme cases, fuel vapor may leak from the fuel tank.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).