免费阅读 · 免费账户即可贡献Anticars(2000)的继任者

GMCGMC Envoy

1998–2009 · 2 各代车型 · 已记录27项缺陷 · 1个市场
各代车型

技术服务通报(TSB)是制造商就已知问题发给经销商的维修说明。它们不是安全召回,但常常能证实某个缺陷。

严重程度全部中等轻微
车型年份
市场全部NA
Envoy II · 2002–2009
通报中等电气NA

通报

本初步信息沟通向技师提供有关间歇性无曲柄、无启动或启动停滞且安全灯亮起的车辆信息。技师可能会发现诊断故障代码B3055、B3

NHTSA · 制造商通报11039894车型年份 2007自动翻译 · 原文:英语查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

本初步信息沟通向技师提供车辆关于间歇性无曲柄、无启动或启动失速且安全灯亮起的情况信息。技师可能会发现诊断故障代码B3055、B3060、B3935、C0750、C0755、C0760、C0765和/或C0775。

NHTSA · 制造商通报11021792车型年份 2007自动翻译 · 原文:英语查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · 制造商通报10232136车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

NHTSA · 制造商通报10219266车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · 制造商通报10200151车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · 制造商通报10114954车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

NHTSA · 制造商通报10114746车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 制造商通报10114354车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

10054E - Special Coverage (customer co-pay discontinued). The contacts on the fuel level sensor may wear prematurely. This wear could cause the fuel gauge to read empty after filling the tank and cause the malfunction indicator light (MIL) to illuminate. As the fuel level in the tank drops, the MIL may turn off and the gauge may display a reading; however, the reading may indicate a slightly higher level of fuel than what is in the tank. Eventually, as the contacts continue to wear, the fuel gauge will stop working and the MIL will illuminate continuously. If the condition occurs within the stated terms, dealers will install a new design fuel level sensor.

NHTSA · 制造商通报10114183车型年份 2005–2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

NHTSA · 制造商通报10113418车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 制造商通报10113177车型年份 2004以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 制造商通报10113120车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 制造商通报10112697车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 制造商通报10112436车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · 制造商通报10111927车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 制造商通报10111737车型年份 2004以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

Diagnostic information on engine oil leak from rear of crankshaft. *tt 05-06-01*022 supplement - crankshaft oil leak repair instrumentions. *tt

NHTSA · 制造商通报10017385车型年份 2005以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

Service engine soon light due a diagnostic trouble code p0606 diagnostic trouble code, operate in reduced engine power mode, and potentially stall. *tt

NHTSA · 制造商通报10017230车型年份 2004以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报中等电气NA

通报

Concerns with no start, turn/hazard, interior lamps, driver information center (dic), radio, theft alarm, wipers, cruise, shift interlock, horn and/or key in signal inoperative. *tt

NHTSA · 制造商通报628833车型年份 2002以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

该技术服务通告提供了某些车辆的相关信息:这些车辆在冷浸后启动时,即使挂入驻车挡(P 挡),也可能出现轻微前后晃动或移动的情况。此时可能伴有"咔嗒"异响。这种移动幅度很小,从车外观察时比驾驶员实际感受到的更为明显,并且在配备自动启动功能的车辆上(如适用)使用该功能时更容易出现。

NHTSA · 制造商通报11009088车型年份 2007自动翻译 · 原文:英语查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

Vehicle Wide Programming(VWP,整车全面编程)是通科用于更新通用汽车(GM)车辆软件的新流程。技师只需在 Techline Connect 中进行一次选择,即可先识别需要更新的模块,然后对受影响的模块进行更新(部分例外情况除外)。模块更新为并行进行,无需技师逐个更新模块。这使经销商和客户的操作流程更加精简高效。

NHTSA · 制造商通报11006621车型年份 2006自动翻译 · 原文:英语查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

NHTSA · 制造商通报10252735车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

NHTSA · 制造商通报10249011车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

Programming And Activation Of Replacement OnStar Modules.

NHTSA · 制造商通报10246951车型年份 2006以原文(英语)显示 · 翻译待完成查看详情 →
Envoy II · 2002–2009
通报轻微电气NA

通报

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · 制造商通报10237387车型年份 2007以原文(英语)显示 · 翻译待完成查看详情 →
更早 →

来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。