意外展开前安全气囊的可能性。
安全气囊前控制单元中的一个电容器可能发生短路。这可能导致安全气囊(s)意外展开。
🔔 注册免费账户,接收 Saab 900 (所有代) 的邮件提醒
安全气囊前控制单元中的一个电容器可能发生短路。这可能导致安全气囊(s)意外展开。
在某些车辆上,安全气囊电子控制单元内部的电气短路可能导致前排安全气囊和安全带预紧器意外展开。 更正措施:经销商将更换安全气囊电子控制单元(ECU)。 注:零部件要到2003年4月才能供货。
某些乘用车。静电可能在前排乘客侧安全气囊模块内积聚,并产生足够大的电荷,从而在触发事件中导致安全气囊意外弹出。这些触发事件大多发生在较凉爽、干燥的天气,通常包括擦拭或清洁仪表板、启动汽车或关闭车门。安全气囊意外弹出可能导致乘员受伤。 纠正措施:经销商将安装前排乘客侧安全气囊模块接地带。
注意:5门车型。这些车辆不符合C.M.V.S.S. 210——安全带总成锚固点的要求。车辆装配时,安全带外侧固定板未经热处理,在某些情况下可能变形并从座椅锚固点脱开。纠正措施:将检查前排安全带,必要时予以更换。
During static testing of belt anchorage points, the outboard attachment plate being used in the testing deformed and detached from the seat anchorage. This does not comply with FMVSS No. 209, "Seat Belt Assemblies," and No. 210, "Seat Belt Assembly Anchorages."
運転者席及び助手席のエアバッグにおいて、制御用モジュールのコンデンサーの耐熱性が 不足しているものがあるため、そのままの状態で使用を続けると、当該コンデンサーから 液漏れが発生することがあり、最悪の場合、回路が短絡して突然エアバッグが展開すると ともにシートベルトプリテンショナーが作動し、運転操作が妨げられるおそれがある。
On certain passenger vehicles, the air bag electronic control unit (ecu) is designed to sense and discriminate frontal impact events, command air bag and seat belt pretensioner deployments in a timely manner, and perform continuous diagnostics of the air bag system in the vehicle. Due to the possible insufficient sealing of the bottom of an electrolyte capacitor, it is possible for it to leak electrolyte within the air bag ecu. Also, in high humidity environments, the operation of the vehicle air conditioner can cause rapid cooling of the ecu, which in turn may cause the formation of condensation with the unit.
助手席のエアバックにおいて、ユニット内のアースが不適切なため、湿度が低いときに、 静電気が帯電し、そのままの状態で使用を続けると、エアバッグユニット内で放電が起り 、最悪の場合、当該エアバックが誤って展開するおそれがある。
A build up of static electricity may cause unintentional deployment of the front passenger air bag.
Vehicle description: Passenger vehicles. Static electricity can build up within the passenger-side air bag module and create enough of a charge to cause an inadvertent air bag deployment. Most of these inadvertent deployments have occurred in cooler, dry weather, and have generally included dusting or wiping of the dashboard, starting the car, or closing the door.
コンバーチブル車両の座席ベルトにおいて、肩ベルトガイドの形状が不適切なため、そ のままの状態で使用を続けると、当該座席ベルトが肩ベルトガイドとベルト巻取装置間で ねじれ、最悪の場合、当該座席ベルトを引き出せなくなるおそれがある。
The tongue at the end of the seat belt has not been hardened to the correct specification.
運転者席及び助手席のシートバックフレーム(座席の背もたれの内部にある鉄製の骨組 み)とリクライニング装置の取付け部に溶接されていないものがあるため、取付け部に過 大な力が加わると、当該座席の背もたれが倒れるおそれがある。
Note: 1994-95 3 and 5 door models and 1995 convertibles. The seat assemblies may be missing one or more of the arc welds that join the seat back recliner mechanism to the seat back frame. This could result in the seat back falling backwards if the vehicle is impacted from the rear. Sudden failure of a driver seat back could occur without prior warning and cause the driver to lose control, resulting in a possible crash. Correction: Seat backs will be inspected and replaced if required.
On some vehicles some welds may be missing from the back frames of the front seats.
The front seats may not lock properly on the longitudinal adjustment/mounting rails.
One or more of the arc welds can be missing on the seat back frame recliner.
運転者席のシートレールに強度不足のものがあり、このままの状態で使用を続けると、最 悪の場合、車両後部等に追突されると当該レールが破損しシートが後方に転倒するおそれ がある。
The driving seat rail on manually adjustable seats may be subject to fatigue cracking.
On certain vehicles equipped with manually adjusted front seats, it is possible that the two (2) trigger springs mounted to the fore/aft adjustment lever on both front seats cannot develop sufficient force to properly lock the seat rails. This could result in the seat moving in the event of a collision. Correction: faulty springs will be replaced with ones with the appropriate trigger spring force.
There is a risk of fatigue cracks around the attachment bushings on the height adjusting mechanism in the driver's seat. In the event of a rear end collision, the height adjuster could break and allow the seat to fold down rearward. Correction: Dealers will replace the seat rails, on the driver's side, with new ones.
Two trigger springs mounted to the fore/aft adjustment lever do not develop sufficient force to properly lock the seat rails. After the seat is adjusted, this does not allow the seat rail lock to properly engage, which can cause the seat to move in a sudden stop or collision.
A weld in the seat rails was not made, increasing the risk of fatigue cracks forming around the attachment bushings on the height adjustment mechanism, causing the possibility of the height adjuster breaking in a rear end collision and allowing the seat to fold backwards.
There may be an insufficient permanent lubrication in the buckle/release mechanism of the type 2 seat belt assemblies. This may cause front seat occupants to have difficulty in fully fastening seat belts, although they may seem to be fully fastened.
Due to insufficient lubrication in the buckle/release mechanism of the front seat belt assemblies,occupants may have difficulty engaging the locking tongue in the latch when putting the belt on.
来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。