يشتبه في تسرب مبرد التكييف أو تقارير عن رائحة رطبة/عفنة داخل المقصورة - إرشادات التشخيص. بيان العميل / نتائج ورشة العمل: نظام التكييف والتبريد لا يبرد / تبريد التكييف أقل من المتوقع / تم تأكيد تسرب مبرد التكييف أو أبلغ العميل عن رائحة رطبة/عفنة داخل المقصورة ملاحظة: في هذا السيناريو يرجى مراجعة المتطلبات المسبقة أدناه - إذا لم يكن هناك تسرب واضح للتهوية وتكييف الهواء وتم الإبلاغ عن رائحة رطوبة/عفن، يجب على العميل أولا التأكد من عدم تسرب المياه إلى المقصورة، يرجى الرجوع إلى جميع مؤشرات التوصيل القابلة للهيكل - إذا لم يكن هناك تسرب ماء واضح، يجب على العامل فحص التكييف والتصريف للجسم بحثا عن انسدادات، وفي حال كانت المصارف مسدودة يجب فك المصارف، وبعد الانتهاء من ذلك يجب على المنفذ التأكد من استمرار رائحة الرطوبة/العفن.
Brake Noise Identification: Customer Statement: -Noise/squeal complaint from the braking system Technical Background: -The noise/squeal can be reproduced and clearly assigned to the braking system
NHTSA · نشرة المصنع10245093سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Running gear - Noise identification Workshop Findings: -The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work
NHTSA · نشرة المصنع10244649سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
NHTSA · نشرة المصنع10242269سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.
NHTSA · نشرة المصنع10240565سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
NHTSA · نشرة المصنع10241847سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Night vision camera - Washer jet leaking. Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet. Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B)
NHTSA · نشرة المصنع10206082سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Engine warning light illuminated within the DIP during acceleration - DTC P029900 evident - W12 TSI only Customer statement: Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost) Workshop findings: DTC P029900 evident within the engine control unit/s In the event the afore mentioned symptoms are evident the operative should refer to the onward instructions
NHTSA · نشرة المصنع10201929سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
NHTSA · نشرة المصنع10201949سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.
NHTSA · نشرة المصنع10201851سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system
NHTSA · نشرة المصنع10201809سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Bentayga - مؤشر تحذير تعليق الهواء داخل لوحة العدادات (DIP) - رمز العطل DTC P089200 رمز الأعراض 3145792 - يظهر في العنوان 74.
بيان العميل: مؤشر تحذير تعليق الهواء داخل لوحة العدادات (DIP).
نتائج الورشة: P089200 رمز الأعراض 3145792 - انقطاع متقطع في دائرة استشعار مرحل الطاقة لوحدة التحكم بالمحرك (TCM) (دائرة مفتوحة في صمامات التحكم بالارتفاع).
الخلفية الفنية: راجع قسم القياس في هذا TPI.
Headlamp switch - Inoperative/Not illuminated - DTC U110B00 within 09-Central Electrics (BCM1). Customer statement: Headlamp switch - Inoperative/Not illuminated Workshop findings - DTC U110B00 within 09-Central Electrics (BCM1) as shown in Figure 1 Figure 1 - Yellow warning light/message within the DIP (Adaptive Lighting Fault) NOTE: Some lighting functionalities can in some cases be lost for example: - Rear fog light activation - All weather lighting mode activation - Headlamps default to dipped beam however high beam will still activate manually NOTE: Recycling the ignition will not resolve the problem Technical background: The issue will not occur when the ignition is on and/or the vehicle is being driven. It occurs as the headlamp switch goes into a sleep state after ignition is Switched OFF, the issue is then evident to the driver when the ignition is next switched ON
NHTSA · نشرة المصنع10186734سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
DTC U112100 evident within diagnostic address 0044 (Steering assistance control module)Customer statement / workshop findings DTC U112100 Databus Missing message evident within the Steering assistance control module - Address (0044) Technical background Refer to the Measure section of this TPI
NHTSA · نشرة المصنع10186684سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
NHTSA · نشرة المصنع10182390سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Front seatbelt - Diagnostic Trouble Codes - B130474 and/or B130574. Customer statement / workshop findings Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings Technical background Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle
NHTSA · نشرة المصنع10182139سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
NHTSA · نشرة المصنع10179439سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Power Steering Noise 4.0 V8 Condition: Power steering noise (Hiss) audible in cabin emanating from front of car Technical Background: Variability in hose assembly and fitting can create noise transfer path at rubber mounting points resulting in power steering hydraulic flow audible in cabin
NHTSA · نشرة المصنع10177077سنوات الطراز 2015معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
NHTSA · نشرة المصنع10171209سنوات الطراز 2009معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Technical product information: Power steering noise 4.0 V8 Customer statement / workshop findings: Power steering noise (hiss) audible in cabin emanating from front of car Technical background: Variability in hose assembly and fitting can create noise transfer path at rubber mounting points resulting in power steering hydraulic flow audible in cabin Measure: In the event of a qualified report of power steering hiss audible in cabin then replace power steering high pressure hose (2) (see Figure 1) Rep.Gr.48 Power Steering Pipes To Remove and Fit
NHTSA · نشرة المصنع10169968سنوات الطراز 2015معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).