قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)

BMW الفئة السابعة E32

1986–1994 · 5 أعطال موثّقة · 4 أسواق
سنة الطراز
السوقالكلNA
استدعاءحرجالمحركNA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

وزارة النقل الكندية30 مايو 19941994096سنوات الطراز 1989–1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءحرجالمحركNA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · الولايات المتحدة11 أبريل 199494V066000سنوات الطراز 1989–1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · الولايات المتحدة4 أغسطس 199898V178000سنوات الطراز 1988–1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

المحرك

في بعض وحدات 318IC، 318IS، 318TI، 325I، 325IC، 325IS، 525I، 525IT، 530I، 530IT، 540I، 740I، 740IL، 840CI وM3، يتم توصيل مثبت السرعة وكابل الخانق بنفس ذراع تشغيل صمام الخانق عند غلاف الخانق. من الممكن أن ينكسر البوشينغ البلاستيكي في أي من الكابلين مما يؤدي إلى انفصال غلاف الكابل الخارجي عن البوشينغ. تطبيق دواسة الوقود بدون تفعيل مثبت السرعة قد يتسبب في تعلق الأنبوب الخارجي بحافة البوش المكسور، مما يؤدي إلى بقاء صمام الخانق مفتوحا جزئيا. إذا حدث ذلك، قد لا تبطئ السيارة كما هو متوقع وقد يحدث حادث. تصحيح: سيتم تركيب مشبك زنبركي على الأنبوب الخارجي لكل كابل لمنع انفصال الكابل من البوشينغ.

وزارة النقل الكندية9 أكتوبر 19971997173سنوات الطراز 1993ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
استدعاءمتوسطالمحركNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · الولايات المتحدة19 أغسطس 199797V131000سنوات الطراز 1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

وزارة النقل الكندية25 أبريل 19941994081سنوات الطراز 1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · الولايات المتحدة3 يناير 199494V022000سنوات الطراز 1993معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

وزارة النقل الكندية13 أكتوبر 19921992129سنوات الطراز 1991معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · الولايات المتحدة10 يوليو 199292V101000سنوات الطراز 1991معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

وزارة النقل الكندية2 مايو 19891989063سنوات الطراز 1988–1989معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

وزارة النقل الكندية2 مايو 19891989062سنوات الطراز 1988–1989معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
استدعاءمتوسطالمحركNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

وزارة النقل الكندية6 أبريل 19891989046سنوات الطراز 1988–1989معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).