Fuel system, gasoline
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
🔔 أنشئ حسابًا مجانيًا لتلقي تنبيهات البريد عن Dodge 600
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor. Consequence of defect: The overheated resistor could ignite and start an instrument panel fire.
On certain vehicles equipped with a 2.2 Litre turbo engine, an inadequately tightened fuel hose clamp at the fuel system pressure regulator could result in fuel leakage and provide the potential for an engine compartment fire.
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: The fuel hose could leak and result in an engine compartment fire.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
On certain vehicles, hydraulic brake tube may interfere with exhaust system hangar bolt and eventually result in brake fluid leakage. This could create a partial loss of braking capability. Should this occur the brake warning light on the instrument panel will warn driver.
On vehicles with power adjusted bucket seats, the driver's seat frame may fail at one of its four attachments. This can result in fore/aft or lateral movement of the seat. This could cause loss of vehicle control and a possible vehicle crash. Correction: The driver's seat frame will be replaced with a strengthened version. Also, the power adjuster crossmember will be reinforced.
Front suspension crossmember may corrode and fail at lower control arm rear pivot mounts if operated where salt is used to aid in snow removal.
Drivers seat frame may experience fatigue failure at one (front/outboard) of its four attachments.
On certain vehicles, the crossmember can become abnormally corroded at the lower control arm attachment. This could result in lower control arm separation and loss of vehicle control. Correction: crossmembers will be inspected and replaced if corrosion is excessive. Remainder will have crossmember retaining brackets installed.
Vehicles equipped with power seats that have had a seat cushion frame replacement in the field could experience cushion frame failure resulting in significant rearward movement of the seat back. This could result in loss of vehicle control and a possible crash. Correction: Seat cushion frame will be inspected and replaced if required.
A service replacement drivers seat cushion (manual seat type) may contain wrong cushion with a brace that could interfere with power seat adjuster mechanism and cause stress on the frame.
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Plugged choke vacuum delay valve. Note: Vehicles equipped with 2.2 litre carbureted engines.
Location of hydraulic brake tube to both rear wheels causes interference and chafing between the tubes and rear suspension trailing arm pivot brackets.
Hydraulic brake tubing routed to the left rear wheel brake system may have been bent out of shape during assembly and could chafe against the exhaust system hanger bolt.
The travel computer system wiring, on the involved vehicles, may be improperly connected. This condition can cause damage to internal components.
On certain vehicles, due to the connection of the travel computer system wiring to the wrong ignition coil terminal, damage to the internal components of the interface module could occur and affect the engine ignition system, possibly causing loss of ignition with inability to restart engine.
The involved vehicles may be equipped with an electrical fuel filler door release which is activated through a coiled current carrying wire (a solenoid). A short in the solenoid could cause sparking at the attaching screws of the solenoid.
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).