On vehicles with four wheel drive and automatic locking front hubs, the front brake hose, between the body brake tubing and the front axle connector, may have been improperly installed (twisted) during vehicle assembly. If twisted, the hose can be looped upon itself in a manner that may allow abrasive contact during normal suspension travel. This could result in eventual hose failure and partial loss of braking capability. Correction: Vehicles will be inspected and brake lines rerouted if necessary.
وزارة النقل الكندية3 يوليو 19871987068سنوات الطراز 1987معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Certain vehicles may have been built with an improperly installed (twisted) front brake hose. This could allow abrasive contact during normal suspension travel and result in eventual hose failure and partial loss of braking capability.
وزارة النقل الكندية10 أكتوبر 19841984122سنوات الطراز 1985معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Vehicles are not in compliance with the impact test requirements of federal motor vehicle safety standard 301, "fuel system integrity." the structure of the rear step bumper may not withstand a rear end collision similar to the force created in testing; fuel leakage may occur upon impact.
NHTSA · الولايات المتحدة24 سبتمبر 198484V115000سنوات الطراز 1980–1985معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
على بعض المركبات، قد تحتوي ناقلات الحركة الأوتوماتيكية على مجموعة قضيب مزلاج وقوف (park sprag rod assembly) قد تعلق في وضع الارتطام بالسن (غير متشابك). في حال حدوث ذلك، قد تتدحرج المركبة من وضع الوقوف وتتسبب في حادث تصادم.
التصحيح: سيتم فحص المركبات، وسيتم استبدال مجموعات قضيب مزلاج الوقوف المشتبه في عيبها.
وزارة النقل الكندية5 يناير 19881988002سنوات الطراز 1988ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
On certain vehicles, the master cylinder may have been overstressed and cracked during cylinder manufacture. A cracked cylinder may fail during braking resulting in loss of vehicle braking capability. This could result in a vehicle crash without prior warning.
وزارة النقل الكندية7 فبراير 19861986020سنوات الطراز 1986معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The front brake hose, which is routed from the body brake tubing to the front axle connector, may have been twisted when installed. If the hose is twisted, it may become looped or coiled upon itself resulting in abrasive contact during normal operation.
NHTSA · الولايات المتحدة24 سبتمبر 198484V117000سنوات الطراز 1985معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Ignition switches installed in the involved vehicles may have been distorted during a crimping operation which resulted in the internal plastic contact carrier of the switch cracking. Pieces of a cracked carrier may break away, permitting abnormal switch electrical contact and the potential for starter actuaton when the switch is turned to the accessory position.
NHTSA · الولايات المتحدة5 أكتوبر 198282V095000سنوات الطراز 1983معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
لقد تُركّب مسامير المشبك على بعض المركبات وقد تحتوي على شقوق. وبمرور الوقت قد تنكسر هذه المسامير، مما يؤدي إلى انفصال المفصل الكروي عن مفصل التوجيه (المحور الدوراني).
NHTSA · الولايات المتحدة27 مايو 198282V055000سنوات الطراز 1982ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).