その他(燃料装置)
燃料注入口のアウターパイプに嵌合しているインナーパイプの溶接位置に不適切なものが あるため、インナーパイプが燃料フィラーキャプのシールと干渉するものがあり、そのま まの状態で使用を続けると、フィラーキャップとアウターパイプの気密性が損なわれ、最 悪の場合、当該部位から燃料蒸発ガスが大気に排出するおそれがある。
🔔 أنشئ حسابًا مجانيًا لتلقي تنبيهات البريد عن Ford Probe (كل الأجيال)
燃料注入口のアウターパイプに嵌合しているインナーパイプの溶接位置に不適切なものが あるため、インナーパイプが燃料フィラーキャプのシールと干渉するものがあり、そのま まの状態で使用を続けると、フィラーキャップとアウターパイプの気密性が損なわれ、最 悪の場合、当該部位から燃料蒸発ガスが大気に排出するおそれがある。
Certain vehicles may not comply with the requirements of CMVSS 1105 - Evaporative Emissions. Fuel vapour may leak from between the fuel cap and the fuel filler pipe. Correction: Filler cap will be replaced with one that incorporates an o-ring that will positively seal the suspect fuel filler pipes.
On certain vehicles, an external spring in the timing belt auto tensioner may break. The broken spring may get caught in the timing belt, resulting in possible engine stalling. Correction: Vehicles will be inspected and affected tensioners will be replaced.
Vehicle description: Passenger vehicles. An external spring in the timing belt tensioner can break and get caught in the timing belt.
تشير اختبارات الامتثال إلى أن هذه المركبات قد تطلق انبعاثات أول أكسيد الكربون (CO) تتجاوز متطلبات انبعاثات العادم بموجب قانون C.M.V.S.S. 1103. تصحيح: سيتم استبدال المحول التحفيزي في المركبات المتأثرة.
ملاحظة: تم استبداله ب 95038. قد لا تلتزم هذه المركبات بانبعاثات العادم C.M.V.S.S 1103. قد تطلق المحفزات انبعاثات تتجاوز المعيار. تصحيح: سيتم استبدال محفزات نظام العادم في المركبات المتأثرة.
Note: Vehicles with 3.0 litre engine. These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. Throttle position sensor may wear prematurely causing interruption of the sensor signal. Correction: Throttle position sensor will be inspected and replaced if necessary.
Vehicles with 3.0l engines and automatic transmissions only. These vehicles do not comply with c.M.V.S.S 1103 - exhaust emissions. Carbon monoxide levels exceed standard. Correction: Dealers will replace the electronic engine control (eec) processor and attach two decals.
Vehicles with 3 litre engines may have throttle levers that were bent during vehicle assembly. If this condition exists, there is a potential that the throttle may stick and not return fully to the idle position. This could cause possible loss of vehicle control. Correction: Vehicles will be inspected and if necessary, the intake manifold assembly will be replaced.
Throttle levers may have been bent during assembly.
車体の中央下部にある副消音器後部の排気管接合部に溶接不良のものがあるため、そのま まの状態で使用を続けると、当該溶接部位に亀裂が発生し、そこから排気ガスが漏れると ともに、騒音が増大するおそれがある。
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).