Some 2023 2024 model year RX 350, RX 350h, RX 500h, and 2024 model year TX 350 and TX 500h vehicles may exhibit a rotational clicking noise from one or both front drive shaft assemblies when accelerating while making turns. This condition may occur without a grease leak present on the front drive shaft assemblies. An updated front drive shaft assembly is available to resolve this condition. Follow the Repair Procedure in this bulletin to address this condition.
NHTSA · نشرة المصنع11034816سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: Careful inspection for paint chips/scratches and body dents/dings. Proper operation of electrical accessories (including interior light, clock, and radio reset). Interior cleanliness. Proper function of mechanical systems. The PDS process helps identify potential vehicle concerns before customer delivery. After completing the PDS process, maintain accurate PDS records by ensuring the required documents listed below are completed and recorded in accordance with Toyota Warranty Policy. GTS+ Health Check Completed PDS Check Sheet Battery Charge Test Print Out GTS+ Tire Pressure Information Customer retention and proper maintenance of vehicles are and have always been a major focus for Lexus. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. This bulletin contains the PDS procedures that apply specifically to 2026 model year TX 350, TX 500h, and TX 550h+ vehicles.
NHTSA · نشرة المصنع11033411سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The 2026 model year Lexus vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the Installation Procedure in this bulletin to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicles glove box for customer reference.
NHTSA · نشرة المصنع11029880سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: Careful inspection for paint chips/scratches and body dents/dings. Proper operation of electrical accessories (including interior light, clock, and radio reset). Interior cleanliness. Proper function of mechanical systems. The PDS process helps identify potential vehicle concerns before customer delivery. After completing the PDS process, maintain accurate PDS records by ensuring the required documents listed below are completed and recorded in accordance with Toyota Warranty Policy. GTS+ Health Check. Completed PDS Check Sheet. Battery Charge Test Print Out. GTS+ Tire Pressure Information. Customer retention and proper maintenance of vehicles are and have always been a major focus for Lexus. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. This bulletin contains the PDS procedures that apply specifically to 2026 model year TX 350, TX 500h, and TX 550h+ vehicles
NHTSA · نشرة المصنع11022967سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2023 2024 model year RX 350, RX 350h, RX 500h, and 2024 model year TX 350 and TX 500h vehicles may exhibit a rotational clicking noise from one or both front drive shaft assemblies when accelerating while making turns. This condition may occur without a grease leak present on the front drive shaft assemblies. An updated front drive shaft assembly is available to resolve this condition.
NHTSA · نشرة المصنع11020653سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
2026 model year Lexus vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the Installation Procedure in this bulletin to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicles glove box for customer reference.
NHTSA · نشرة المصنع11015924سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
2025 model year Lexus vehicles are equipped with driver side floor mat retaining hooks (clips) to secure the floor mat in the correct position. In addition, some models may also utilize retaining hooks (clips) for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the Installation Procedure in this bulletin to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retaining hooks (clips).
NHTSA · نشرة المصنع11014189سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: Careful inspection for paint chips/scratches and body dents/dings. Proper operation of electrical accessories (including interior light, clock, and radio reset). Interior cleanliness. Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Lexus. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. This bulletin contains the PDS procedures that apply specifically to 2025 model year TX 350, TX 500h, and TX 550h+ vehicles. Refer to the universal Check Sheet that contains PDS steps that apply to all 2025 model year Lexus vehicles. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the PDS Check Sheet.
NHTSA · نشرة المصنع11012748سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2023 2024 RX 350, RX 350h, and 2024 TX 350 vehicles may exhibit a rotational clicking noise from one or both front drive shaft assemblies when accelerating while making turns. This condition may occur without a grease leak present on the front drive shaft assemblies. An updated front drive shaft assembly is available to resolve this condition.
NHTSA · نشرة المصنع11010099سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2022 2024 model year Lexus vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev1: Applicability has been updated to include 2024 model year GX 550, LX 600, NX 250, NX 350, NX 350h, NX 450h+, RX 350, RX 350h, RX 450h+, RX 500h, RZ 300e, RZ 450e, TX 350, TX 500h, and TX 550h+ vehicles. The Introduction section has been updated. The Operation Procedure section has been removed. The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.
NHTSA · نشرة المصنع11003639سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2022 2024 model year Lexus vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev1: Applicability has been updated to include 2024 model year GX 550, LX 600, NX 250, NX 350, NX 350h, NX 450h+, RX 350, RX 350h, RX 450h+, RX 500h, RZ 300e, RZ 450e, TX 350, TX 500h, and TX 550h+ vehicles. The Introduction section has been updated. The Operation Procedure section has been removed. The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.
NHTSA · نشرة المصنع11003584سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
TSB: 2024 model year Lexus vehicles are equipped with driver side floor mat retaining hooks (clips) to secure the floor mat in the correct position. In addition, some models may also utilize retaining hooks (clips) for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the Installation Procedure in this bulletin to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retaining hooks (clips).
NHTSA · نشرة المصنع10248829سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
TSB: 2025 model year Lexus vehicles are equipped with driver side floor mat retaining hooks (clips) to secure the floor mat in the correct position. In addition, some models may also utilize retaining hooks (clips) for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the Installation Procedure in this bulletin to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retaining hooks (clips).
NHTSA · نشرة المصنع10248830سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
تخضع البطارية في السيارة المخزّنة لظروف يمكن أن تقلل من أدائها وعمرها الافتراضي. وتشمل هذه الظروف مدة التخزين، ودرجة الحرارة، والاستنزاف الطفيلي، وحمل البطارية. ونظرًا لهذه العوامل، يلزم فحص البطارية وصيانتها لضمان التشغيل السليم وإطالة عمرها الأمثل.
إثناء عملية التصنيع، تُركَّب الإطارات على المركبة في مجموعات متطابقة للمساعدة في تقليل حالات مثل الانحراف أو الميلان الجانبي. وإذا تم استبدال العجلات أو إعادة تشطيبها قبل تسليم المركبة، فمن المهم أن تبقى الإطارات على المركبة في نفس الموضع وباتجاه الدوران نفسه.
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be implemented to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicles systems and components. Any problems that are found should be corrected immediately.
NHTSA · نشرة المصنع11037180سنوات الطراز 2027معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation.
Translation:
خلال عملية التصنيع، تُركَّب الإطارات على المركبة كمجموعات متطابقة للمساعدة في تقليل حالات مثل السحب أو الانحراف. وإذا تم استبدال العجلات أو إعادة تشطيبها قبل تسليم المركبة، فمن المهم أن تبقى الإطارات على المركبة في الموضع نفسه وباتجاه الدوران نفسه.
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA · نشرة المصنع11034820سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicles systems and components. Anyproblems that are found should be corrected immediately.
NHTSA · نشرة المصنع11034815سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA · نشرة المصنع11029886سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).