قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)

Mazda سي إكس-3

2014– · 13 أعطال موثّقة · 3 أسواق

النشرات الفنية (TSB) تعليمات إصلاح يرسلها المصنعون إلى وكلائهم بشأن مشكلات معروفة. ليست استدعاءات سلامة، لكنها كثيرًا ما تؤكد وجود عطل.

سنة الطراز
السوقالكلNA
نشرةمتوسطالهيكلNA

نشرة

تحل هذه النشرة محل النشرة (النشرات) الصادرة سابقاً والمدرجة أدناه. التغييرات مبينة باللون الأحمر. 09-012/21 12/13/21, 06/10/21 and 04/27/21 الوصف قد يواجه بعض العملاء جميع الأعراض التالية: لن يعمل قفل/فتح الأبواب باستخدام زر جهاز الإرسال عن بُعد. 1. لن يعمل قفل/فتح الأبواب باستخدام مستشعر اللمس الخاص بقفل/فتح الباب. 2. لن يبدأ تشغيل المحرك باستخدام مفتاح الإشعال. 3. يعمل جهاز الإرسال من تلقاء نفسه. 4. تنفد بطارية المفتاح بشكل أسرع من المعتاد. 5. الأعراض 1-3: قد يحدث ذلك عند تعرض جهاز الإرسال عن بُعد لحمل زائد، مما يؤدي إلى تشوه الأطراف الكهربائية وضعف التلامس مع البطارية. للقضاء على هذه المشكلة، تم تعديل هيكل جهاز الإرسال عن بُعد للحد من تشوه الأطراف الكهربائية. الأعراض 4-5: قد يحدث ذلك عند تعرض جهاز الإرسال عن بُعد لحمل مفرط، مما يخلق فجوة حول الحشية تدخل من خلالها الرطوبة فتآكل لوحة الدوائر، وهو ما يؤدي بدوره إلى استنزاف بطارية المفتاح بشكل أسرع من المعتاد. للقضاء على هذه المشكلة، تمت زيادة سماكة جدار الهيكل على سطح تركيب الحشية، وتحسين قوة الترابط بين المكونات لمنع التشوه. إجراء الإصلاح إذا كانت البطارية تالفة أو مركبة بشكل غير صحيح، فاستبدل البطارية و/أو أعد تركيبها بشكل صحيح. إذا كانت وظيفة توفير الطاقة عن بُعد متوقفة، وكانت البطارية سليمة ومركبة بشكل صحيح، فاستبدل جهاز الإرسال عن بُعد المعيب بجهاز معدّل وفقاً للتعليمات الواردة في MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: لا تستبدل أجهزة الإرسال عن بُعد الأخرى الخاصة بالمركبة إذا لم تكن تعاني من أي مشكلة.

NHTSA · نشرة المصنع11034436سنوات الطراز 2021ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). It does not start charging. It stops charging with the indicator flashing in red after starting. It stops charging without any visible sign after starting. For CX-50, some customers may experience that despite placing the MagSafe-equipped iPhone at the center of the wireless charger, charging stops after about ten seconds. MagSafe-equipped iPhones use magnets to align the charger and the device. When charging MagSafe-equipped iPhones with a non-MagSafe compatible charger, improper alignment can cause the magnetic field required for charging to be disrupted by the magnets, significantly reducing charging efficiency.

NHTSA · نشرة المصنع11012342سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

MNAO has recently found an increase in non-returned cores within the United Radio (UR) exchange program. As a reminder, dealers have 90 days, after the order is placed, to return the exchanged part. Failure to return the exchanged part will result in a debit of the full component price. It is highly recommended to set a calendar reminder at the time of the order for no more than 60 days to ensure all orders are returned if repaired and if not repaired, contact the customer to cancel the order and return the unit.

NHTSA · نشرة المصنع10243559سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). - It does not start charging. - Soon after starting, it stops charging with the indicator flashing in red. - Soon after starting, it stops charging without any visible sign. These symptoms may be caused by improper control software of the wireless charger (Qi). To eliminate these concerns, the specification of the wireless charger (Qi) has been modified. NOTE: The modifications for the symptoms are different depending on the model.

NHTSA · نشرة المصنع10243549سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · نشرة المصنع10218722سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

NHTSA · نشرة المصنع10185967سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light improperly illuminates when driving on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Please contact the Hotline for a countermeasure repair if a vehicle arrives with this issue. A countermeasure control module is due in July for this concern.

NHTSA · نشرة المصنع10185959سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · نشرة المصنع10185957سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped.

NHTSA · نشرة المصنع10185907سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3" even when driving straight on a flat road.

NHTSA · نشرة المصنع10185904سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · نشرة المصنع10186336سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطأخرىNA

نشرة

A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)

NHTSA · نشرة المصنع10186252سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

A/C blows warm air. Some customes may complain about warm air from the climate control vents. This may be caused by condenser corrosion, causing a refrigerant leak.

NHTSA · نشرة المصنع10185803سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · نشرة المصنع10185813سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · نشرة المصنع10168119سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطأخرىNA

نشرة

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · نشرة المصنع10159199سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · نشرة المصنع10159196سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction).Master Warning Light, Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light, Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light, High Beam Control (HBC) system Warning Light (amber). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · نشرة المصنع10155440سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · نشرة المصنع10154528سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · نشرة المصنع10154531سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · نشرة المصنع10154454سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · نشرة المصنع10153226سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطأخرىNA

نشرة

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · نشرة المصنع10153304سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 and U0401:00 stored in the PCM memory when engine cranking is interrupted and on A/T vehicles, DTC U0442:00 is also stored. This concern most likely occurs when the brake pedal is released during engine cranking. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. DTC U0401:00 - Signal error from PCM DTC U0442:00 - [TCM] Invalid data received from PCM. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · نشرة المصنع10148004سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles may experience a check engine light on and/or failsafe with DTC P061B:00 stored in the PCM. This condition will likely occur as a result of one of the following causes: Engine cranking was interrupted by releasing the brake pedal. Start button was double pressed while the engine was still cranking. A countermeasure to correct mis-detection is currently being prepared.

NHTSA · نشرة المصنع10144336سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
الأقدم →

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).