قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)

Mazda CX-30

2019– · 1 الأجيال · 15 أعطال موثّقة · 3 أسواق
الأجيال
كل الأجيالCX-302019–1531216

النشرات الفنية (TSB) تعليمات إصلاح يرسلها المصنعون إلى وكلائهم بشأن مشكلات معروفة. ليست استدعاءات سلامة، لكنها كثيرًا ما تؤكد وجود عطل.

سنة الطراز
السوقالكلNA
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present.

NHTSA · نشرة المصنع11030600سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain about a very low frequency noise and/or vibration felt at the steering wheel, the floor and/or the seats when driving at 1500-1650 rpm in any gear position. This may be caused by normal vehicle behavior while the cylinder deactivation is active (two cylinders drive). The state of the cylinder deactivation can be monitored in the center display to help verify if this is the issue.

NHTSA · نشرة المصنع11014789سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.

NHTSA · نشرة المصنع11013792سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطناقل الحركةNA

نشرة

The A/T (Automatic Transmission) warning light is flashing in the instrument cluster at new car delivery, without any DTCs being present.

NHTSA · نشرة المصنع10244559سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into R position. * The screen freezes and goes to a white screen, then the system reboots. * The steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms: - No sound emitting from the speakers. - Audio source selection is unavailable. * The vehicle icon rotates when using the navigation with head-up mode. * Beep sounds every after couple of minutes. * Language setting may not be accepted correctly. * The audio track may not pause when pressing the mute button. * The system reboots. * The screen may turn black when trying to play a video file in the USB connected device.

NHTSA · نشرة المصنع10226900سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some customers may experience a no start because the battery is discharged after the vehicle is parked for more than 8 hours. This may be caused by one or more of the following, resulting in excessive parasitic draw (dark current) on the battery. 1. The vehicle control system may not have gone to sleep because a key fob was left in the vehicle after the ignition switch was turned off and the doors were closed. This is caused by improper BCM control logic which allows a higher parasitic draw (approx. 6A) to continue for approximately 6 minutes until the vehicle control system goes into sleep mode. If the doors are operated frequently for car washing or luggage loading/unloading etc., it prevents the vehicle control system from sleeping during that time. 2. The parking lights may have been left on because the warning sound for lights on is a short ding, and it may not be noticed. 3. [With Full-Auto A/C] The climate control unit may not have gone to sleep because the hazard warning switch was pressed after the ignition was turned off. This is caused by improper control logic of the climate control unit. To correct these concerns: 1. The control software of the body control module (BCM) has been modified to shorten the time until going into the sleep mode to approximately 2 minutes. 2. The control software of the body control module (BCM) has been modified to change the lights on warning sound to a continuous one. 3. The control software of the climate control unit has been modified.

NHTSA · نشرة المصنع10218723سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles may have a "Low Battery Risk. Start Vehicle to Charge 12V Battery" warning message in the instrument cluster and a 30 second alarm sound. This is caused by the vehicle's electrical control area network (CAN) entering "Sleep Mode" when the network awake time reaches 30 cumulative minutes without the engine running. The vehicle network starts to wake-up at the moment any side door is opened in order to increase the start-up speed of electrical components and the network awake cumulative time count begins by the customer doing any one of the following wake-up triggers: Open any door(s), Unlock doors, Open liftgate, Depress brake pedal, Push start/stop button, Other operations that wake-up the network. No dealer visit is required. The warning message can be cleared by starting the engine and idling or driving for 5 minutes or longer.

NHTSA · نشرة المصنع10206940سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesnt appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.

NHTSA · نشرة المصنع10203724سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesn't appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 - 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.

NHTSA · نشرة المصنع10202685سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. NOTE: SA-045/21 HAS BEEN SUPERCEDED TO SSPC7.

NHTSA · نشرة المصنع10200938سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.

NHTSA · نشرة المصنع10200937سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · نشرة المصنع10200935سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · نشرة المصنع10200934سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.

NHTSA · نشرة المصنع10199636سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles may have a "Low Battery Risk. Start Vehicle to Charge 12V Battery" warning message in the instrument cluster and a 30 second alarm sound. This may be caused by the customer doing any one of the following several times without starting the engine for an extended period of time: Open any door(s), Unlock doors, Open liftgate, Depress brake pedal, Push start/stop button. No dealer visit is required. The warning message can be cleared by starting the engine and idling or driving for 5 minutes or longer.

NHTSA · نشرة المصنع10186807سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience a no start because the battery is discharged after the vehicle is parked for more than 8 hours. This may be caused by one or more of the following, resulting in excessive parasitic draw (dark current) on the battery.

NHTSA · نشرة المصنع10185046سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some customers may experience an intermittent static sound coming from the audio speakers. After ignition OFF. While driving (ignition ON). When opening the driver's door to enter the vehicle. The infotainment system may recover after: IGN OFF - ON. Removing and installing the Audio fuse. Disconnecting and reconnecting the battery terminal.

NHTSA · نشرة المصنع10182112سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some customers may experience an intermittent static sound coming from the audio speakers. After ignition key OFF While driving (key ON). When opening the driver's door to enter the vehicle. The infotainment system may recover after: IGN OFF - ON Removing and installing the Audio fuse. Disconnecting and reconnecting the battery terminal.

NHTSA · نشرة المصنع10180718سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX30. Inform the customer that Mazda is actively investigating this issue and apologizes for any inconvenience. Mazda would like to request both dealer and customer support to expedite a repair. Customers having this concern should be instructed to contact Mazda Roadside Assistance and have their vehicle inspected by a local dealer.

NHTSA · نشرة المصنع10179166سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالتعليقNA

نشرة

On some vehicles, the Commander switch might be inoperative. This could be caused by fuse F13 (15A) being removed instead of F15 (15A) at the factory in the lower panel compartment on the left side of the steering wheel.

NHTSA · نشرة المصنع10179164سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالفراملNA

نشرة

Some vehicles equipped with Smart Brake Support (SBS) may exhibit a front radar system malfunction message in the instrument cluster with DTC C1A67:04 (front radar sensor internal malfunction) stored in memory. This may be caused by water penetrating into the front radar sensor through the breather hole when exposed to a great amount of water and damaging the radar sensor, resulting in the DTC C1A67:04. To eliminate this concern, the front radar sensor has been modified.

NHTSA · نشرة المصنع10179085سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالهيكلNA

نشرة

Some customers may experience a no start because the battery is discharged after the vehicle is parked for more than 8 hours. This may be caused by one or more of the following, resulting in excessive parasitic draw (dark current) on the battery. 1. The vehicle control system may not have gone to sleep because a key fob was left in the vehicle after the ignition switch was turned off and the doors were closed. This is caused by improper BCM control logic which allows a higher parasitic draw (approx. 6A) to continue for approximately 6 minutes until the vehicle control system goes into sleep mode. If the doors are operated frequently for car washing or luggage loading/unloading etc., it prevents the vehicle control system from sleeping during that time. 2. The parking lights may have been left on because the warning sound for lights on is a short ding, and it may not be noticed. 3. [With Full-Auto A/C] The heater control unit may not have gone to sleep because the hazard warning switch was pressed after the ignition was turned off. This is caused by improper control logic of the heater control unit.

NHTSA · نشرة المصنع10179078سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

MSP57 - 2020 CX-30 WIRELESS CHARGING PAD LED STAYS ON: Concern Outline: The Wireless Charging Pad power indicator LED light does not shut off when the vehicle ignition is cycled off and the accessory remains functional in all conditions which may drain power from the battery due to an incorrect installation procedure. Only vehicles with the accessory installed at Port Salamanca are affected. Action Required: The Wireless Charging Pad function will be inspected for proper operation. If found to remain functional with the vehicle turned off, the Wireless Charging Pad must be replaced and installed correctly with the current kit available by placing an order in eMDCS. There are 286 vehicles in dealer inventory that must be repaired prior to delivery. Vehicles in Dealer Inventory will be posted to MGSS and updated weekly. Vehicles delivered with this MSP57 not repaired are subject to a debit of the New Car Ready claim.

NHTSA · نشرة المصنع10177970سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX-30. Inform the customer that Mazda is actively investigating this issue and apologizes for any inconvenience. Mazda would like to request both dealer and customer support to expedite a repair. Customers having this concern should be instructed to contact Mazda Roadside Assistance and have their vehicle inspected by a local dealer.

NHTSA · نشرة المصنع10177934سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
نشرةمتوسطالكهرباءNA

نشرة

If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

NHTSA · نشرة المصنع10177853سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
الأقدم →

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).