Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present.
NHTSA · نشرة المصنع11030600سنوات الطراز 2026معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers
NHTSA · نشرة المصنع11003356سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Please be advised that the valve stem seals assigned to the 2.5 Skyactiv Turbo engines in GEPC are incorrect. The Diesel Valve Stem seal SH09-10-1F5A, which is for Diesel engines, is currently listed for these models in GEPC. Please ensure that the proper valve stem seals are used for the 2.5 Skyactiv Turbo engines affected by SSPD5 have the correct valve seal part number PY8W-10-1F5 installed on PYT engines to avoid any potential issues.
NHTSA · نشرة المصنع11000679سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.
NHTSA · نشرة المصنع10254184سنوات الطراز 2024معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into R position. * The screen freezes and goes to a white screen, then the system reboots. * The steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms: - No sound emitting from the speakers. - Audio source selection is unavailable. * The vehicle icon rotates when using the navigation with head-up mode. * Beep sounds every after couple of minutes. * Language setting may not be accepted correctly. * The audio track may not pause when pressing the mute button. * The system reboots. * The screen may turn black when trying to play a video file in the USB connected device.
NHTSA · نشرة المصنع10226900سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
## عدم بدء التشغيل المتقطع (لا يدور المحرك / لا يبدأ التشغيل)
قد يشكو بعض العملاء من عدم دوران المحرك أو عدم بدء التشغيل بشكل متقطع. وقد يكون السبب هو ضعف توصيل مجموعة أسلاك لوحة العدادات عند الموصل C12. قد لا يكون موصل المرآة الإضافية مع البوصلة و T-harness عند العمود A على جانب السائق مثبتًا بشكل صحيح (مقفلًا). لحل شكوى العميل، قم بتثبيت مجموعة أسلاك لوحة العدادات بإحكام، وكذلك الموصلين العلوي والسفلي C12.
Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesnt appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.
NHTSA · نشرة المصنع10203724سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesn't appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 - 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.
NHTSA · نشرة المصنع10202685سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.
NHTSA · نشرة المصنع10200937سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
NHTSA · نشرة المصنع10200935سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
NHTSA · نشرة المصنع10200934سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.
NHTSA · نشرة المصنع10199636سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.
NHTSA · نشرة المصنع10194774سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may have a "Low Battery Risk. Start Vehicle to Charge 12V Battery" warning message in the instrument cluster and a 30 second alarm sound. This may be caused by the customer doing any one of the following several times without starting the engine for an extended period of time: Open any door(s), Unlock doors, Open liftgate, Depress brake pedal, Push start/stop button. No dealer visit is required. The warning message can be cleared by starting the engine and idling or driving for 5 minutes or longer.
NHTSA · نشرة المصنع10186807سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
INSTRUMENT CLUSTER WARNING MESSAGE "SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED" AND DTC U0401:68 IS STORED:Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.
NHTSA · نشرة المصنع10170828سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
WARNING MESSAGE SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED WITH DTC U2511:68: Some customer's may compain about warning message "Safety And Driver Support Systems Partially Disabled" with the following DTC's stored: U2511:68 DSC - Error signal received from electrical supply unit (ESU) U2511:68 VCM - Brake light control signal error. REPAIR PROCEDURE: U2511:68 DSC - Error signal received from electrical supply unit (ESU) Go to DTC U2511:68 [DSC HU/CM] U2511:68 VCM - Brake light control signal error Information is currently missing from Workshop Manual. MGSS will be updated soon. See service information below:
NHTSA · نشرة المصنع10170826سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · نشرة المصنع10185813سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · نشرة المصنع10168119سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit DTC B14F0:76 [VCM] (Forward sensing camera (FSC) deviation) stored in memory and the i-ACTIVSENSE warning light (amber) on after BCM replacement. This is caused by the learning value of the forward sensing camera (FSC) aiming being initialized after BCM replacement due to a software malfunction of the FSC. To correct this concern, the FSC software will be modified to not initialize the value of the FSC aiming after BCM replacement.
NHTSA · نشرة المصنع10166849سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If a customer comes in with the following concerns, contact Hotline for assistance. OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON, DTC P055F and/or P0524 stored, No drivability concern or engine mechanical noise, Outside the VIN range in TSB 01-020/18.
NHTSA · نشرة المصنع10165353سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customer may experience all of the following when turning the ignition ON under hot weather conditions such as parking under the hot sun for some period of time: i-ACTIVSENSE warning light ON (1), Smart Brake Support (SBS) indicator light ON (2), "Excessive Camera Temp. Drive Safely" or "Safety and Driver Support Systems Temporarily Disabled" warning messages, DTC B14F9:00 stored in memory. DTC B14F9:00 cannot be found on MGSS, therefore repair cannot be performed.
NHTSA · نشرة المصنع10164053سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit DTC U2120:00 and/or U2500:82 stored in memory and the i-ACTIVSENSE warning light (amber) ON when turning ON the ignition after any electronic control unit (ECU) is reprogramed or configured using MDARS. NOTE: ECU stands for general units (cameras and modules), all of which can be reprogrammed. This is caused by a software malfunction of the forward sensing camera (FSC). To correct this issue, the FSC software will be modified.
NHTSA · نشرة المصنع10164075سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).