هيّ التعرض المطوّل لأشعة الشمس قد يتسبب في تدهور الغلاف البلاستيكي لتجميعة لسان حزام الأمان الأمامي الذي يثبّت قضيب القفل، وانزياحه من موضعه. وقد يؤدي ذلك إلى انفصال اللسان عن شريط حزام الأمان، مما يجعل حزام الأمان عديم الفائدة لشاغل المركبة.
تصحيح: سيتم إبلاغ المالكين بأن شركة فورد ستقوم بإصلاح أحزمة الأمان التي تعاني من هذه الحالة.
وزارة النقل الكندية28 سبتمبر 19921992117سنوات الطراز 1984–1985ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.
NHTSA · الولايات المتحدة29 أبريل 199292V063000سنوات الطراز 1984–1985معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
وزارة النقل الكندية17 مايو 19881988066سنوات الطراز 1981–1983معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
NHTSA · الولايات المتحدة20 ديسمبر 198383V134000سنوات الطراز 1984معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
وزارة النقل الكندية17 ديسمبر 19831983114سنوات الطراز 1984معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.
NHTSA · الولايات المتحدة8 سبتمبر 198181V102000سنوات الطراز 1981معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.
وزارة النقل الكندية4 سبتمبر 19811981092سنوات الطراز 1981معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).