Steering:Gear box (other than rack and pinion)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
🔔 أنشئ حسابًا مجانيًا لتلقي تنبيهات البريد عن Pontiac فايربيرد (كل الأجيال)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
These vehicles may have been built with an improperly assembled steering intermediate shaft. This condition could cause the intermediate shaft lower coupling to loosen and rotate on the steering gear input shaft. If this were to occur while the vehicle was in motion, a loss of steering control could result and a crash could occur without prior warning. Correction: Steering shaft will be inspected and lower coupling will be replaced if required.
يمكن أن تتشقق نقطة لحام عنق فتحة تعبئة الوقود أو أن تظهر بها تسربات على شكل ثقوب دبوسية، وهو ما لا يتوافق مع المعيار الفيدرالي الأمريكي لسلامة المركبات الآلية رقم 301 (FMVSS No. 301)، "سلامة نظام الوقود". ويمكن للشقوق والثقوب أن تسمح بتسرب أبخرة الوقود والوقود نفسه.
هذه المركبات قد تظهر عليها شقوق أو "ثقوب دبوسية" عند لحام وصلة عنق فتحة تعبئة الوقود. وقد يؤدي ذلك إلى رائحة وقود أو تسرب للوقود. وفي حال وجود مصدر اشتعال، قد يؤدي تسرب الوقود الناتج عن هذه الحالة إلى نشوب حريق في المركبة. التصحيح: سيتم فحص خزانات الوقود في المركبات المتأثرة بحثًا عن التسربات، وستُستبدل عند الحاجة.
Note: Vehicle located in ontario. The fuel line could develop a hole due to contact with the hot air (air injection reaction) check valve. This could result in fuel leakage and an engine compartment fire. Correction: Fuel line bundle will be inspected for heat damage and replaced if necessary. Fuel line bundle will also be rerouted.
The fuel lines on these vehicles may have been misrouted and may contact the "air" check valve. The high temperatures from the "air" check valve could allow it to melt through and damage a fuel line.
Fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly.
Fuel return hoses may break at either crimped coupling.
Note: Vehicles equipped with 5.0 litre and 5.7 litre engines. Vehicles may have fuel return hoses which could break at either or both crimped couplings. If a coupling were to separate, fuel leakage and a possible engine compartment fire could result. Correction: A properly crimped fuel return hose will be installed on all involved vehicles.
Note: Vehicles equipped with 2.8.L v6 engines. The fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly. This could result in fuel leakage and an engine compartment fire. Correction: A redesigned fuel feed hose will be installed on all involved vehicles.
The hub area of the wheels may not be structurally sound and thus subject to fracture. Consequence of defect: The wheels could separate from the car causing a loss of control. This could result in an accident without prior warning.
Due to undersized grinding at the time of manufacture, the rear brake centre flex hoses could separate from the end fittings when subjected to the pull force required by cmvss 106-74. Tensile strangth test. Such a separation would result in loss of brake fluid and a partial loss of braking action. Should this happen while the vehicle is in motion, at a time when minimum stopping distances are required, a vehicle crash could occur without prior warning.
The involved vehicles do not conform to federal motor vehicle safety standard no. 210, "seat belt assembly anchorages". The non-compliance exists because the rear seat belt anchorages may pull through the underbody of the vehicle if enough force is applied.
Fuel tank ventilator valve in the fuel system may produce a loud and persistent "whistle" during venting of the tank. If the fuel filler cap is removed while this condition exists and the tank is more than 3/4 full, gasoline may be forced out of the filler neck onto bystanders.
على بعض المركبات، تحتوي بكرات أحزمة الأمان في مقاعد الصف الخلفي على أوضاع قفل أولى لا تُقفل عند استخدامها من قِبل الركاب الأصغر حجمًا. وهذا لا يتوافق مع متطلبات المعيار الفيدرالي لسلامة المركبات الآلية رقم 208، "حماية الركاب من الاصطدام".
## وصف المركبة لا تتوافق بعض المركبات الركابية مع متطلبات المعيار الفيدرالي لسلامة المركبات الأمريكي رقم 208، "حماية الركاب عند التصادم"، والمعيار رقم 214، "حماية الجانب عند الاصطدام الجانبي". قد تحتوي هذه المركبات على لحامات قرب مفصل باب السائق السفلي لا تستوفي المواصفات.
## وصف المركبة المركبات الركابية المزودة بناقل حركة يدوي. قد يكون أسطوانة التحكم الرئيسية للقابض (الماستر سيلندر) قد صُنعت بحلقة احتجاز غير صحيحة.
ملاحظة: تنطبق هذه المعلومات على المركبات المزودة بمحركات سعة 5.7 لتر. قد يتعطل صمام إعادة تدوير غازات العادم (EGR) بسبب التآكل الداخلي. وقد يؤدي ذلك إلى عدم استيفاء المركبة لمتطلبات الانبعاثات المعمول بها. التصحيح: سيقوم الوكلاء بفحص صمام EGR والتحقق من رقم الجزء، واستبداله عند الضرورة بصمام EGR بتصميم جديد.
Note: Convertible vehicles. These vehicles do not comply with c.M.V.S.S. 209 - seat belt assemblies. The front seat belt retractors may lock-up on slopes less severe than the requirement of the standard. As a result, occupants may not be able to extract and fasten their seat belts until the vehicle is moved to a more level surface. Correction: Dealers will inspect for proper front seat belt retractor position and those found to be improperly positioned will be reinstalled correctly.
These vehicles were manufactured with seat belt retractors out of design position which can cause the retractor to lock-up on slopes less severe than the fmvss requirement. This does not comply with fmvss no. 209, "seat belt assemblies."
Note: Vehicles equipped with 4l60 automatic transmissions. The shift control cable conduit may separate and prevent the transmission from being shifted into the proper position, for example, the transmission shift lever may be in the park position when the transmission is actually in drive or reverse. This condition may cause unexpected vehicle movement and could result in a vehicle crash without prior warning. Correction: A revised shift control lever will be installed on affected vehicles.
The automatic transmission shift control cable can separate.
These vehicles may not comply with c.M.V.S.S. 209 - seat belt assemblies. - seat belt latch plates may not engage or may do so only after wiggling and/or forcing the latch plate. Correction: Vehicles will be inspected and suspect retractor side safety belt assemblies (which include latch plates) will be replaced if necessary.
The metal latchplates may not engage the buckle assemblies, causing a "no latch" condition. Movement of the seat occupant in this condition could cause latchplate release from the buckle.
على بعض المركبات، قد يحتوي نظام فرامل الركن على مُعدِّل فرامل ركن غير فعّال. وقد يؤدي ذلك إلى فقدان تدريجي لفعالية فرامل الركن مع تآكل الوسادات الخلفية للقرص. ونتيجة لذلك، قد لا تتمكن فرامل الركن من تثبيت المركبة على منحدر شديد. وإذا تُركت المركبة متوقفة وناقل الحركة في وضع الحياد أو في أحد التروس الأمامية، فقد تتدحرج المركبة بعيدًا، ما قد يؤدي إلى إصابات شخصية أو أضرار بالممتلكات. التصحيح: سيتم تركيب مُعدِّل فرامل ركن جديد.
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).