The short section of high pressure fuel hose between the fuel rail and the fuel pressure regulator, which runs alongside the intake manifold, may be subject to hardening. In the event that this line does harden, fuel leaks could develop between the hose and metal pipe fittings. Leaking fuel could ignite on the hot exhaust system and lead to an engine compartment fire. Correction: Fuel hose will be replaced on 924s, 944 and 944 turbo vehicles and the fuel hose and fuel rail will be replaced on 944s vehicles.
وزارة النقل الكندية4 أبريل 19901990051سنوات الطراز 1987–1988معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The hose material used in the short section of the high pressure fuel line hose, between the fuel rail and fuel pressure regulator, is subject to hardening, and could cause fuel leaks between the hose and the metal pipe fittings.
NHTSA · الولايات المتحدة2 أبريل 199090V061000سنوات الطراز 1987–1988معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The rear spring plates (radius arms) on these vehicles may have been improperly tempered by supplier. Improperly hardened spring plates could crack and possibly break . This could affect lateral guidance of the corresponding rear wheel resulting in loss of vehicle control.
وزارة النقل الكندية9 أكتوبر 19851985110سنوات الطراز 1982معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Rear spring plates may not have been tempered and are not of the proper hardness value. Consequence of defect: The plates could crack and/or break, affect lateral guidance of the rear wheel, and result in loss of control of the car which may cause an accident.
NHTSA · الولايات المتحدة26 يوليو 198585V095000سنوات الطراز 1982معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The rear seat belts do not include emergency-locking or automatic-locking retractors. The belts do not comply with federal motor vehicle safety standard no. 208, "occupant crash protection".
NHTSA · الولايات المتحدة26 أكتوبر 198383V111000سنوات الطراز 1982معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The bridge for the seat belt locking (inertia retractor) mechanism on one suppliers belts may have been improperly crimped. This condition may result in a non-locking retractor.
وزارة النقل الكندية28 سبتمبر 19791979167سنوات الطراز 1980معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The bridge in the seat belt buckle locking mechanism of the front seat belt assembly may have been improperly bent. The buckle may not hold properly and will release, if extreme forces are applied.
NHTSA · الولايات المتحدة27 سبتمبر 197979V222000سنوات الطراز 1980معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Vehicles were inadvertently equipped with a 1979 model vehicle emission control information label which contains an incorrect vacuum hose touting diagram. These vehicles do not comply with the labelling requirements of canada motor vehicle safety standard 1101 - emission devices.
وزارة النقل الكندية6 مايو 19801980070سنوات الطراز 1980معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).