Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Audi 80 B2 (81)

1978–1986 · 3 dokumentierte Mängel · 2 Märkte
Modelljahr
MarktAlleNA
RückrufKritischKarosserieNA

Rückruf

In the rear trunk area, the right rear side member for the mounting buffer may not have been welded according to specifications. In the event of an accident resulting in rear end damage it is possible that the right rear side member could break loose, damaging the fuel tank and causing fuel leakage.

Transport Canada27. März 19811981039Modelljahre 1980–1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischBremsenNA

Rückruf

The interior surface of the threaded hole for the front brake caliper brake hoses may contain porous spots which would allow brake fluid to seep out of the calipers during heavy brake applications. Prolonged seepage will eventually reeduce brake fluid level in the reservoir and may lead to complete brake failure.

Transport Canada12. Nov. 19801980148Modelljahre 1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelGetriebeNA

Powertrain

On vehicles with automatic transmission, a low oil level in the differential could cause premature bearing and gear wear and eventual failure of the differential. This could result in possible drive wheel lock-up and loss of vehicle control. Correction: Differential will be drained and oil will be replaced with an advanced design high performance gear oil. Owners will be provided with a revised maintenance schedule.

Transport Canada22. Jan. 19931993008Modelljahre 1985–1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelGetriebeNA

Power train:Axle assembly

The differential oil of the transaxle is lost over time due to evaporation. Low oil levels cause premature bearing and gear wear and eventual failure of the differential.

NHTSA · USA11. Jan. 199393V006000Modelljahre 1985–1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Engine

On vehicles with automatic transmission, the idle stabilizer valve may experience excessive wear. Such wear causes idle fluctuations which are barely noticeable at first, but ultimately could result in unsatisfactory driveability. Correction: Idle stabilizer valve will be replaced. V.I.N. Range wau***8**fa000001 to wau***8**ga138778

Transport Canada26. Mai 19871987054Modelljahre 1985–1986Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelSonstigesNA

Vehicle speed control

Excessive wear of idle stabilizer could cause idle fluctuations.

NHTSA · USA18. Mai 198787V069000Modelljahre 1985–1986Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seats And Restraints

The seat belt buckles manufactured by afg and located on the rear seat of the audi 4000 and the right front seat of the audi 5000 may not lock securely, although the metal tongue of the seat belt has been fully engaged. In the event of an abrupt brake application or on impact, these buckles could become unlocked. Correction: Vehicles will be inspected and all seat belt buckles manufactured by afg will be replaced. V.I.N. Range audi 4000 - wau***8*ga*124887 to wau***8*ga*137554 audi 5000 - wau**44*g**087473 to wau**44*g**099448

Transport Canada4. Sept. 19861986098Modelljahre 1986Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seat belts:Front:Buckle assembly

Rear or front right seat belt locks may not properly engage. Consequence of defect: Seat belts could separate in event of heavy brake application or impact and thus subject passengers to injury.

NHTSA · USA18. Aug. 198686V113000Modelljahre 1986Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Fuel system, gasoline:Fuel injection system

The fuel pump may stop functioning without warning. This can occur because an electrical connector in the fuse panel may overheat and interrupt the electrical circuit.

NHTSA · USA9. Nov. 198383V117000Modelljahre 1980–1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelKarosserieNA

Structure:Frame and members

Rear bumper system on certain vehicles may not have been properly welded during assembly. In the event of a rear end collision, the right side bumper supportor could break loose, damage the fuel tank and allow fuel to leak.

NHTSA · USA24. März 198181V039000Modelljahre 1980–1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Service brakes, hydraulic:Foundation components:Disc:Caliper

On certain vehicles, porous spots may have developed on the interior surface of the threaded hole for the brake hose during the moulding process. These spots allow brake fluid to seep from the calipers during heavy brake applications.

NHTSA · USA12. Nov. 198080V146000Modelljahre 1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).