Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
HLK-Kältemittelleckage vermutet oder Berichte über einen feuchten/muffigen Geruch in der Kabine – Diagnoserichtlinien. Kundenaussage / Werkstattfindung: HLK nicht gekühlt / HLK-Kühlung weniger als erwartet / KHLK-Leckage bestätigt oder Der Kunde meldet einen feuchten/muffigen Geruch in der Kabine Hinweis: Für dieses Szenario beachten Sie bitte die unten aufgeführten Voraussetzungen – Sollte kein HVAC-Leck nachweisen und ein feuchter/muffiger Geruch gemeldet/identifiziert wurde, sollte der Mitarbeiter zunächst bestätigen, dass kein Wasser in die Kabine sickert, bitte alle VIN geltenden TPIs konsultieren – Sollten keine Wasserlecks vorliegen, sollte der Mitarbeiter die HVAC- und Karostabläufe auf Verstopfungen überprüfen; falls die Abflüsse verstopft sind, müssen die Abflüsse entstopft werden; sobald dies erledigt ist, sollte der Mitarbeiter prüfen, ob der feuchte/muffige Geruch noch vorhanden ist.
Bremsgeräuscherkennung: Kundenaussage: -Lärm-/Quietschbeschwerde vom Bremssystem Technischer Hintergrund: -Das Geräusch/Quietschen kann reproduziert und eindeutig dem Bremssystem zugeordnet werden
Running gear - Noise identification Workshop Findings: -The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
Night vision camera - Washer jet leaking. Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet. Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B)
Engine warning light illuminated within the DIP during acceleration - DTC P029900 evident - W12 TSI only Customer statement: Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost) Workshop findings: DTC P029900 evident within the engine control unit/s In the event the afore mentioned symptoms are evident the operative should refer to the onward instructions
Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.
Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system
Headlamp switch - Inoperative/Not illuminated - DTC U110B00 within 09-Central Electrics (BCM1). Customer statement: Headlamp switch - Inoperative/Not illuminated Workshop findings - DTC U110B00 within 09-Central Electrics (BCM1) as shown in Figure 1 Figure 1 - Yellow warning light/message within the DIP (Adaptive Lighting Fault) NOTE: Some lighting functionalities can in some cases be lost for example: - Rear fog light activation - All weather lighting mode activation - Headlamps default to dipped beam however high beam will still activate manually NOTE: Recycling the ignition will not resolve the problem Technical background: The issue will not occur when the ignition is on and/or the vehicle is being driven. It occurs as the headlamp switch goes into a sleep state after ignition is Switched OFF, the issue is then evident to the driver when the ignition is next switched ON
DTC U112100 evident within diagnostic address 0044 (Steering assistance control module)Customer statement / workshop findings DTC U112100 Databus Missing message evident within the Steering assistance control module - Address (0044) Technical background Refer to the Measure section of this TPI
Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
Front seatbelt - Diagnostic Trouble Codes - B130474 and/or B130574. Customer statement / workshop findings Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings Technical background Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle
Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
Power Steering Noise 4.0 V8 Condition: Power steering noise (Hiss) audible in cabin emanating from front of car Technical Background: Variability in hose assembly and fitting can create noise transfer path at rubber mounting points resulting in power steering hydraulic flow audible in cabin
Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
Technical product information: Power steering noise 4.0 V8 Customer statement / workshop findings: Power steering noise (hiss) audible in cabin emanating from front of car Technical background: Variability in hose assembly and fitting can create noise transfer path at rubber mounting points resulting in power steering hydraulic flow audible in cabin Measure: In the event of a qualified report of power steering hiss audible in cabin then replace power steering high pressure hose (2) (see Figure 1) Rep.Gr.48 Power Steering Pipes To Remove and Fit
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).