Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Due to an implementation error in various OBD diagnostics in the vehicle's control units, in very rare cases itmay happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.
Several complaints are possible: Vehicle does not start Gear cannot be engaged Various Check Control Messages Malfunction indicator lamp (MIL) on Several Check Control messages are possible: It is possible to continue driving. High-voltage system. You can continue driving. Drivetrain. Restart not possible. Drivetrain fault. Call Roadside Assistance. Drivetrain failure. Information: Total error of vehicle. The following fault memory entries are stored in the CCU: D796D9 - Message (- 0x91) not up-to-date, receiver CCU, transmitter EME D796DC - No message (- 0x91), receiver CCU, transmitter EME D796D8 - No message (- 0x91), receiver CCU, transmitter EME Other fault codes below may be stored in the EGS BA09B8 Inverter, Voltage Sensor, 5V HV AUX: Out of range or open connection detected BA0A45 ECU internal: Internal error of the synchronous serial data bus. Additional fault memory entries are possible. Similar fault memory entries indicating a missing EMEmessage (Traction E-Machine Electronic) can also be stored in other control units.
When navigation is selected, only the start animation with the text Starting navigation system... isdisplayed. The Navigation application does not start. This only applies to vehicles where Navigation hasbeen enabled and has been verified to work previously.
?BMW AG has issued a Delivery Stop (effective July 12, 2023) on certain Model Year 2023 - 2024 BMW vehicles that were produced between July 21, 2022, and July 11, 2023. A software logic error in the diagnostic module for tank leaks (DMTL) could cause the Service Engine Soon light (MIL) to not turn on when there is an electrical fault with pump or diverter valve for the DMTL even after several driving cycles with the fault/s being currently present.
BMW AG has issued a Delivery Stop (effective July 12, 2023) on certain Model Year 2023 - 2024 BMW vehicles that were produced between July 21, 2022, and July 11, 2023. A software logic error in the diagnostic module for tank leaks (DMTL) could cause the Service Engine Soon light (MIL) to not turn on when there is an electrical fault with pump or diverter valve for the DMTL even after several driving cycles with the fault/s being currently present.
Nach der Programmierung des Fahrzeugs über ISTA/RSUto I-Level 26-03-5xx kann der Kunde berichten, dass einige der Innenumgebungsbeleuchtungsstreifen (Pfeile) nach einem tiefen Schlafzyklus sporadisch ausfallen. Dieses Problem ist vorübergehend und die Innenumgebungsbeleuchtung wird nach dem Verriegeln/Entriegeln des Fahrzeugs oder einer Änderung der Farbauswahl von selbst wiederhergestellt.
Aufgrund ungünstiger Software zeigt die Storage Management Electronics (SME) keine Fehlercodes an, die die Malfunction Indicator Lampe (MIL) auslösen, wenn die ISTA-Servicefunktion "Display Permanent SAE Fault Codes" ausgeführt wird. Daher müssen Werkstätten SME-spezifische permanente SAE-(emissionsbezogene) Diagnosefehlercodes (DTCs) identifizieren, die im Fahrzeug während der Diagnose oder bei der Vorbereitung eines Fahrzeugs auf eine staatliche Emissionsinspektion und Wartung gespeichert sind, durch ein Umgehungsverfahren.
After programming the vehicle via ISTA/RSUto I-level 26-03-5xx, some of the interiorambient lighting strips (arrows) may begin tofail sporadically after a deep sleep cycle.
The Central Information Display (CID) side of the Multifunction Display (MFD) may flicker intermittently. Theflickering manifests itself in three phases: The image is distorted The central information display turns black (black screen) The image is OK again The complete flickering episode with all the above-mentioned three phases only lasts about half a second intotal each time.
The vehicle may experience various operational issues with Apple CarPlay Projected Modes such as: Dropped connections No automatic reconnection Display errors
An error in the Battery Management Electronics (SME) can lead to an interruption in communication, which can lead to the high-voltage system being turned off. The error is indicated by a Check Control message, and it is generally possible to continue driving until the vehicle is parked.
The malfunction indicator lamp (MIL) is triggered by the erroneous fault code 031BFC- AC charging,charging electronics 2, internal fault: No internal capacitor discharge stored in the CCU. However, AC charging is operating as designed without a charging concern or issue. Affected PHEV vehicles have the CCU-03 (7.4 kW / 11 kW) with I-levels from 24-07-500 to 25-11-5xx.
Malfunction indicator lamp (MIL) is triggered by the erroneous fault code(s) BA0023 - Control unit: internalfault (software group fault) In addition, the BA0008 - CCU, internal coolant temperature sensor:Signal implausible faults may be stored in the CCU memory. However, AC charging is still operating as designed, without any related drivability complaints. Affected PHEV vehicles have the CCU-03 (7.4 kW / 11 kW) with I-levels from 24-07-500 to 25-11-5xx.
The malfunction indicator lamp (MIL) is triggered and 0318E2 AC charging, charging electronics 1,component protection: Overload current on AC side fault may be stored during AC charging Level 1(120 VAC). Note: Despite the fault memory entry (and the malfunction indicator lamp), the AC charging process willcontinue operating as designed and there is no related drivability complaint. Affected PHEV (plug-in hybrid electric vehicle) vehicles with CCU-03 (7.4 kW combined charging unit).
After replacing the Multifunctional Display (MFD), the Central Information Display (CID) is black. Thebacklight of the CID is illuminated, and touch function does register an audible sound.
The malfunction indicator lamp (MIL) is triggered and 0318E2 AC charging, charging electronics 1,component protection: Overload current on AC side fault may be stored during AC charging Level 1(120 VAC). Note: Despite the fault memory entry (and the malfunction indicator lamp), the AC charging process willcontinue operating as designed and there is no related drivability complaint. Affected PHEV (plug-in hybrid electric vehicle) vehicles with CCU-03 (7.4 kW combined charging unit).
The malfunction indicator lamp (MIL) may be triggered by the erroneous fault code: BA0023 - Control unit: internal fault (software group fault) In addition, the BA0008 - CCU, internal coolant temperature sensor: Signal implausible faults may be stored in the CCU memory. However, AC charging will still operate as designed, without any related drivability complaints. Affected PHEV (plug-in hybrid electric vehicle) vehicles with CCU_P1 (7.4 kW and 11 kW) with I-levels from 24-07- 500 to 25-11-5xx.
SITUATION The malfunction indicator lamp (MIL) is triggered by the erroneous fault code 031BFC- AC charging, charging electronics 2,internal fault: No internal capacitor discharge stored in the CCU. However, AC charging is operating as designed without a charging concern or issue. Affected PHEV vehicles have the CCU-03 (7.4 kW / 11 kW) with I-levels from 24-07-500 to 25-11-5xx
The vehicle may experience various operational issues with the Multifunction Display such as: Intermittent black screen Permanent black screen Intermittent head unit functions not displayed (i.e., Navigation screen only is black)
The vehicle may experience various operational issues with the infotainment system such as: Resets of the head unit Delayed start-up of the head unit (longer than 30 seconds) Failed start-up of the head unit Sporadic or permanent problems with navigation Sporadic or permanent Bluetooth connection problems Sporadic or permanent audio problems Sporadic or permanent speech / IPA (international phonetic alphabet) problems Missing displays, radio stations, camera images or applications
RSU availability. Due to a software error in the BCP, the Calibration Identification Number (CAL ID) and the Calibration Verification Number (CVN) of the vehicle are not stored correctly. They are generated with eachprogramming session and are used to identify official BMW software.
RSU availability. Due to a software error in the BCP, the Calibration Identification Number (CAL ID) and the CalibrationVerification Number (CVN) of the vehicle are not stored correctly. They are generated with each programming session and are used to identify official BMW software.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).