Bulletin
Certain vehicles listed above may have a condition in which there is a water leak due to a partially seated tail-lamp harness grommet. Dealers will inspect and reseat grommet if necessary.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Chevrolet Bolt (alle generationen) erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Certain vehicles listed above may have a condition in which there is a water leak due to a partially seated tail-lamp harness grommet. Dealers will inspect and reseat grommet if necessary.
Fixes to help ensure start reliability and prevent battery drain Improved charging performance and messages Improved performance for anti-lock braking system
Certain vehicles may have a condition in which a fastener may be loose at the steering column to cockpit beam. Dealers will inspect the fasteners and torque them to the proper value.
Improvements to traction and stability control on uneven terrain Improvements to braking performance on low-traction surfaces Improvements to assisted braking Improvements to active cabin ventilation Additional protection for the health of your battery Updates to help prevent excessive battery drain and overheating Improvements to the software update system
Improvements to diagnostics and service messaging for battery health, particularly in humid conditions. Improvements to transmission diagnostics used for shifting. Improvements to charging system diagnostics. Fixes to help protect EV adapter from overheating while charging.
This informational bulletin provides information for dealers/technicians on Changes to Park Assist and Reverse Automatic Braking for Certain 2022 Passenger Car, Crossover, SUV, and Truck Models Equipped with RPO 00Y and/or 00Z.
Stop Delivery. Vehicles were shipped to the dealer without the hood insulator. Install the hood insulator.
Customer Satisfaction Program. Certain vehicles may have oil leaking from one or more of the plugs on the drive unit assembly. If not addressed, the drive unit could be damaged due to the loss of fluid over time, and the driver may hear abnormal grinding and scraping noises if extreme oil leakage occurs. Dealers are to apply Loctite between the housing and the four plugs and tighten plugs as required.
This service bulletin provides warranty labor operation restriction information for dealers/technicians on Park Assist, Heated/Vented Seats, and/or Heated Steering Wheel Options and Features are Inoperative.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This informational bulletin provides information on 6.6L Duramax Possible Oil Leak Path Information.
This informational bulletin provides information for dealers/technicians on Changes to Park Assist and Reverse Automatic Braking for Certain 2022 Passenger Car, Crossover, SUV, and Truck Models Equipped with RPO 00Y and/or 00Z.
This warranty administration service bulletin provides warranty labor operation restriction information for dealers/technicians on Park Assist, Heated/Vented Seats, and/or Heated Steering Wheel Options and Features are Inoperative for vehicles that may have had options built without modules due to semiconductor shortage.
This informational bulletin provides information for dealers/technicians on Changes to Heated Steering Wheel for Certain 2022 Passenger Car, Crossover, SUV, and Truck Models Equipped with RPO 00G.
This Preliminary information communicates to technician's if they have a low mileage vehicle with an Air Conditioning inoperative condition with a P0534 to inspect the Air Compressor for leak and the possible area of the leak. Once verified of the leak in the compressor area to replace the compressor for the repair.
Malfunction Indicator Lamp (MIL) Illuminated - DTC P1AE6 Set Important: Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Install the EL-49642 SPS Programming Support Tool to maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOTconnect a battery charger. Refer to Hybrid Powertrain Control Module 2 Programming and Setup in SI.
Door Trim Panel Gap Along Top After Front or Rear Trim Panel Installation Some customers or technicians may comment on seeing a gap between the top pad trim (1) and support panel (2) on a front or rear door trim panel. The condition is most common after the trim panel has been installed during a repair The cause of the condition may be that during a repair, the door pad top trim piece can become unseated when the door pad is pulled off of the clips that secure the door trim panel to the door. Do not replace the door panel for this condition. The gap can be eliminated by firmly pressing down and fully seating the top trim on the door panel.
This Preliminary Information communication advises the technician to a possible Drive Unit fluid plug leak that a dealer may find, it alsoaddresses the locations of the plugs that the technician may need to inspect for the possible leak. The Preliminary Information addresses the procedures and tools recommended for the repair to address the leak and also advises the recommended sealant that is needed for the repair along with the Labor Operation Time with OLH (Other Labor Hours) time needed to perform the repair.
This Preliminary Information communication advises the technician to a possible Drive Unit fluid plug leak that a dealer may find, it alsoaddresses the locations of the plugs that the technician may need to inspect for the possible leak. The Preliminary Information addresses the procedures and tools recommended for the repair to address the leak and also advises the recommended sealant that is needed for the repair along with the Labor Operation Time with OLH (Other Labor Hours) time needed to perform the repair. Updated to referenceA202309280 - Customer Satisfaction ProgramOil Leak at Plugs of Drive Unit Assembly
This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair a non-working heated steering well. This provides the path and procedures to perform testing for a possible incorrect part installed at the factory.
This Preliminary Information communication advises the technician that Electronic Brake Control Module, Brake Pressure Modulator Valve, Power Brake Master Cylinder Booster Assembly and the Master Cylinder for the Chevrolet Bolt EV will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
This bulletin provides a procedure to perform a HPCM2 update or install a Battery Energy Control Module if DTCs P1AE6, P1FFF or P0ABB set.
This informational bulletin provides information for dealers/technicians on a fix regarding a door trim panel gap along the top after front or rear trim panel installation.
This informational bulletin advises the possible concerns that can happen when using a stop leak additive in the cooling system.
This information bulletin explains how the wrong sticker was installed on the IBooster and how it needs to be removed and discarded.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).