Bulletin
Start-Stop-Ladeleuchte leuchtet, Intelligenter Batteriesensor (IBS) Ladezustand (SOC) ungenau, Meldung zum Laden der Batterie, Vorhandensein von IBS-bezogenen Diagnostic Trouble Codes (DTCs) oder Batteriewarnleuchte an
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Chrysler 200 (alle generationen) erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Start-Stop-Ladeleuchte leuchtet, Intelligenter Batteriesensor (IBS) Ladezustand (SOC) ungenau, Meldung zum Laden der Batterie, Vorhandensein von IBS-bezogenen Diagnostic Trouble Codes (DTCs) oder Batteriewarnleuchte an
Start-Stop-Ladeanzeige leuchtet, Intelligenter Batteriesensor (IBS) Ladezustand (SOC) ungenau, Meldung zum Laden der Batterie, Vorhandensein von IBS-bezogenen Diagnosefehlercodes (DTCs) oder Batteriewarnleuchte an
Start-Stop-Ladeleuchte leuchtet, Intelligenter Batteriesensor (IBS) Ladezustand (SOC) ungenau, Meldung zum Laden der Batterie, Vorhandensein von IBS-bezogenen Diagnosefehlercodes (DTCs) oder Batteriewarnleuchte an
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.
Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
Gear Assy - Steering Rack & Pinion Electric
2016 JK WRANGLER wind noise or water leak coming from a void in the windshield sealer
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2172 - High Airflow/Vacuum Leak Detected ? P1D73 - AGS Performance ? U0140 - Lost Communication With Body Control Module
Front Brake Moan Noise While Stopping In Reverse
Rear Brake Squeal Noise In Reverse This bulletin involves replacing the rear brake pads. The customer may describe a squeal noise from the rear brakes. Noise is only present during the first few brake applies in reverse. Noise is most prevalent at low temperatures around -12 to -4 degrees C (10 to 25 degrees F) after an overnight cold soak and during low brake pedal apply pressure. Noise goes away after approximately 5 brake applies.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) **P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak.** P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10C to 0C (14F to 32F).
Kundenzufriedenheitsmitteilung T12 VECI-Etikett Das Fahrzeugemissions-Kontrollinformations-Etikett (VECI-Etikett) bei etwa 120.000 der oben genannten Fahrzeuge enthält möglicherweise keine Emissionskontrollinformationen. Das VECI-Etikett wird häufig bei der Prüfung und Wartung im Betrieb (Inspection and Maintenance, I/M) verwendet, um die ordnungsgemäße Funktion emissionsrelevanter Bauteile zu überprüfen. Falsche Angaben auf dem VECI-Etikett könnten im Bundesstaat Kalifornien zur Verweigerung der Fahrzeugzulassung führen. Ein neues VECI-Etikett muss installiert werden.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. U1424 - Implausible Engine Torque Signal Received. P1185 - General Pressure Sensor Correlation. P0101 - Mass Air Flow Sensor "A" Circuit Performance. P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. U0402 - Implausible Data Received From TCM. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open.
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
Rear Brake Squeal Noise In Reverse This bulletin involves replacing the rear brake pads. The customer may describe a squeal noise from the rear brakes. Noise is only present during the first few brake applies in reverse. Noise is most prevalent at low temperatures around -12 to -4 degrees C (10 to 25 degrees F) after an overnight cold soak and during low brake pedal apply pressure. Noise goes away after approximately 5 brake applies.
Rear Brake Squeal Noise In Reverse This bulletin involves replacing the rear brake pads. The customer may describe a squeal noise from the rear brakes. Noise is only present during the first few brake applies in reverse. Noise is most prevalent at low temperatures around -12 to -4 degrees C (10 to 25 degrees F) after an overnight cold soak and during low brake pedal apply pressure. Noise goes away after approximately 5 brake applies.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles, built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2015 PF Vehicles, built on or before January 08, 2015 (MDH 0108XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2172 - High Airflow/Vacuum Leak Detected ? P1D73 - AGS Performance ? U0140 - Lost Communication With Body Control Module
Part Description: Engine Cover Issue Description: The Chrysler 200 LX (Model UFCE41) is the only model in the 200 Family built without an engine cover. Please do not order this part as a shortage and error on this model. Cover may be installed with customer pay.
Poor AC Performance This bulletin involves inspecting the A/C condenser for leakage and replacing if required. The customer may experience poor A/C performance from the HVAC system due to refrigerant loss through the condenser.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module.
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation.** P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made:
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).