Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Check Engine Light On and Transmission Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P072F-00 - Stuck In Gear 4. Customers may also comment on the following: During normal vehicle operation, while decelerating from 7th gear, the MIL illuminates and the vehicle enters a limp-in (reduced power) mode. This bulletin involves performing the transmission "QuickLearn" procedure using wiTECH.
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 - Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. P084F-00 - Park-Neutral Switch Output Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. Service Charging System and Traction Battery Cutoff warning messages appear during a key cycle event at -7 C (+20F). Vehicle will force to Park when keyed off in Neutral if the door is open during wake-up procedure and remains open or within 2 minutes of door closure Loss of power steering assist when ignition push-button is pressed by driver after a Remote Start. Unusual battery drain when DTC, P084F-00 - Park-Neutral Switch Output is set. This software release includes the following software enhancements: Corrections to allow the vehicle to clear the permanent fault codes. 12V battery overcharged prevention. Corrected fuel consumption counter while in charge depleting This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P16F0-00 - SPI Comm Hardware Fault. P16F1-00 - Internal SPI Communication. Customers may experience the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Clunk noise heard while the vehicle is moving. Transmission fluid is leaking and may prohibit vehicle movement. Vehicle does not move when shifted into Drive or Reverse gear. Loss of heat from the engine. Vehicle may lose propulsion capability upon entering Ready Mode. Vehicle may lose propulsion while driving in electric mode. Prior to that, a warning message will appear in the cluster informing them to stop safely because the vehicle will be shutting down soon. After shutting down, the vehicle may not be able to start again. Failure may occur between driving cycles and may not start after trying to turn it on for the first time during a day. This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. P0CF3-00 - Control Pilot Circuit Open (North America Only). P0CF4-00 - Control Pilot Circuit Performance (North America Only). P0D57-00 - Proximity Detection Circuit Performance (North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop (APAC China Only). Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Clunk noise heard while the vehicle is moving. Transmission fluid is leaking. Vehicle does not move when shifted into Drive or Reverse gear This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
Flash: Auxiliary Hybrid Control Processor (AHCP) / Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. P0CF3-00 - Control Pilot Circuit Open (North America Only). P0CF4-00 - Control Pilot Circuit Performance (North America Only). P0D57-00 - Proximity Detection Circuit Performance (North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop (APAC China Only). Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. This bulletin involves reprogramming the AHCP and then the HCP with the latest available software.
Flash: Auxiliary Hybrid Control Processor (AHCP) / Customers **must** experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle **must** SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance.** P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 - Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. P084F-00 - Park-Neutral Switch Output Customers may also comment on one or more of the following: **Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine.** Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. Service Charging System and Traction Battery Cutoff warning messages appear during a key cycle event at -7 C (+20F). Vehicle will force to Park when keyed off in Neutral if the door is open during wake-up procedure and remains open or within 2 minutes of door closure Loss of power steering assist when ignition push-button is pressed by driver after a Remote Start. Unusual battery drain when DTC, P084F-00 - Park-Neutral Switch Output is set. This software release includes the following software enhancements: Cor
Flash: Auxiliary Hybrid Control Processor (AHCP) / Customers **must** experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle **must** SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance.** P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. P0CF3-00 - Control Pilot Circuit Open (North America Only). P0CF4-00 - Control Pilot Circuit Performance (North America Only). P0D57-00 - Proximity Detection Circuit Performance (North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop (APAC China Only). Customers may also comment on one or more of the following: **Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine.** Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. , Special Tools, LOP and Policy sections, updated Claims Data statements, and an updated Repair Procedure.
Flash: Auxiliary Hybrid Control Processor (AHCP) / Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Clunk noise heard while the vehicle is moving. Transmission fluid is leaking. Vehicle does not move when shifted into Drive or Reverse gear. This bulletin involves reprogramming the AHCP and then the HCP with the latest available software.
Flash: Auxiliary Hybrid Control Processor (AHCP) / Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance.** P16F0-00 - SPI Comm Hardware Fault. P16F1-00 - Internal SPI Communication. Customers may experience the following: **Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Clunk noise heard while the vehicle is moving. Transmission fluid is leaking and may prohibit vehicle movement. Vehicle does not move when shifted into Drive or Reverse gear. Loss of heat from the engine.** Vehicle may lose propulsion capability upon entering Ready Mode. Vehicle may lose propulsion while driving in electric mode. Prior to that, a warning message will appear in the cluster informing them to stop safely because the vehicle will be shutting down soon. After shutting down, the vehicle may not be able to start again. Failure may occur between driving cycles and may not start after trying to turn it on for the first time during a day. , LOP, and Repair Procedure. Other changes not asterisked include the removal of a build date. REPAIR SUMMARY:
Flash: Auxiliary Hybrid Control Processor (AHCP) / **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine.** Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Vehicle will not start when it is cold (-30C / -22F and below). Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. , Special Tools and Policy sections, new LOP, updated Claims Data information and an updated Repair Procedure.
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:U1431 - Implausible Data Received From Cruise Control Module.P24B9 - EVAP System Leak Detection Pump Pressure Sensor Circuit Range/Performance. P0300 - Multiple Cylinder Misfire. P1C64-00 - Hybrid Perf Engine Speed Below Target During Autostart.
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:U1431 - Implausible Data Received From Cruise Control Module.P24B9 - EVAP System Leak Detection Pump Pressure Sensor Circuit Range/Performance. P0300 - Multiple Cylinder Misfire. P1C64-00 - Hybrid Perf Engine Speed Below Target During Autostart.
A/C Suction/Liquid Line, A/C Discharge Dine, A/C Compressor For RU bodies ONLY; Issues with leaks in the above A/C components. Also issues with compressor performance. Before replacing any of the components listed above call Michael Romm at cell (248) 766-5465. If no response in 15 minutes, please proceed with repair. Be prepared to answer the following questions: - Is A/C functional or not? - If not, does HVAC have the latest software per TSB 24-006-16 ? - Is compressor clutch engaging? If not, then using wiTECH, was A/C request active when clutch was not engaging? - Is there any evidence of refrigerant leaks / dye anywhere in the A/C system? - If the refrigerant has been reclaimed, what was the amount?
"Flash: Transmission Control Module (TCM) Updates The following software advancements are available: Transmission Shift Quality Improvements. This bulletin involves reprogramming the TCM with the latest available software."
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1AC6-00 - MCPA Crankshaft Position Signal Sensor Performance. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0031 - O2 Sensor 1/1 Heater Circuit Low. P0032 - O2 Sensor 1/1 Heater Circuit High. P0037 - O2 Sensor 1/2 Heater Circuit Low. P0038 - O2-Sensor 1/2 Heater Circuit High. P0051 - O2-Sensor 2/1 Heater Circuit Low. P0052 - O2-Sensor 2/1 Heater Circuit High. P0057 - O2 Sensor 2/2 Heater Circuit Low. P0058 - O2-Sensor 2/2 Heater Circuit High. The following modules need to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0AA1-00 - Hybrid/Ev Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0B3C-00 - Hybrid-Ev Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid-Ev Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid-Ev Battery Voltage Sense 3 Circuit Performance P0B4B-00 - Hybrid-Ev Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/Ev Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/Ev Battery Voltage Sense 6 Circuit Performance. Engine will run in fuel oil refresh mode often and customer may be prompted to get an oil change before needed. Software corrects real time clock synchronization with Powertrain Control Module (PCM) and BPCM. In the previous software, after a battery replacement, the timing for when an oil&fuel change was due was reset to zero, instead of being dependent on the mileage. All new replacements packs will receive this software update.
Flash: Powertrain Control Module (PCM) Updates This bulletin involves updating the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor A. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor A. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor B. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor B.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).