Die Kupplungsdruckplatte kann brechen, während sich das Fahrzeug in Bewegung befindet.
Die Kupplungsdruckplatte kann während der Fahrt brechen. Dies kann zu einer Fehlfunktion des Getriebes und zu einem erhöhten Brandrisiko des Motors führen.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Ford Focus 2nd generation erhalten
Die Kupplungsdruckplatte kann während der Fahrt brechen. Dies kann zu einer Fehlfunktion des Getriebes und zu einem erhöhten Brandrisiko des Motors führen.
Localized overheating of the engine cylinder head may cause the cylinder head to crack.This may cause a pressurized oil leak which in extreme circumstances could result in a fire in the engine compartment.
Korrosion am Mehrwegeventil des Erdgassystems kann auftreten. Im Brandfall könnte dies zu einer Fehlfunktion der Druckentlastungseinrichtung führen, mit der Gefahr, dass der Erdgastank explodiert.
Ingenieurtechnische Untersuchungen haben ergeben, dass Fahrzeuge, die in Ländern mit hohem Streusalzeinsatz während der Wintermonate betrieben werden, einem erhöhten Risiko von Korrosionsablagerungen ausgesetzt sein können. In extremen Fällen kann sich die Korrosion bis in die elektronischen Schaltkreise ausbreiten und zu Überhitzung führen. In seltenen Fällen kann die Überhitzung so stark sein, dass sich das Modul sowie die umliegende Verkabelung und Bauteile entzünden.
In Ländern, in denen die Straßen im Winter intensiv gesalzen werden, besteht die Gefahr, dass am Steuergerät des Kühlerlüfters Korrosion entsteht.
null Vehicles operated in countries which have high road salt usage during the winter months may experience an increased risk of corrosion build up. In extreme cases the corrosion can spread into the electronic circuits and result in overheating. In rare cases the module and wiring components may ignite.
Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite.
null Vehicles operated in countries which have high road salt usage during the winter months may experience an increased risk of corrosion build-up. In extreme cases, the corrosion can propagate into the electronic circuits and result in overheating. In rare cases, the overheating may be sufficient to ignite the module fitted to the engine cooling fan and surrounding wiring component increasing the risk of a fire.
Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite.
Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite.
Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite.
It has been identified that a batch of vehicles converted by SVP have been fitted with a split charging system the relays of which may not be to specification and could subsequently fail. This can result in wiring loom damage and the possibility of a fire.
It has been identified that due to a specification change to the engine cooling fan module vehicles operated in countries which have high road salt usage during the winter months may experience an increased risk of corrosion build up. In extreme cases the corrosion can penetrate the electrical circuits and result in overheating. In rare cases the overheating may be sufficient to ignite the cooling fan control module and surrounding wiring whilst the vehicle is parked.
It has been identified that a batch of vehicles may have been fitted with section of power assisted steering hose that is not to specification. This could result in premature failure of the hose with loss of steering assistance and in extreme cases the possibility of an engine bay fire occasioned by escaping hydraulic fluid coming into contact with hot components.
Certain vehicles fail to conform to the requirements specified in federal motor vehicle safety standard no. 208, 'occupant crash protection.' the driver air bag module may not have been properly assembled.
During engine warm up it is possible that the non return valve within the vacuum pump may stick. It is possible that if sufficient brake applications are made before the valve releases the vacuum stored within the brake booster will be used up and a hard brake pedal and longer stopping distances may result.
The rear hub retaining bolts may become loose because some bolts are not to the required specification.
It has been identified that on affected vehicles the roll over protection system securing bolts may either be loose or not fully tight. In this condition the roll over protection may not be fully effective in the event of a roll over occurring.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).